AnalogX - Revision history

Brentp: /* Introduction */

2020-09-06T17:59:34Z

Introduction

← Older revision		Revision as of 17:59, 6 September 2020
Line 3:		Line 3:

	[[image:AnalogX_icons.jpg\|640px]]		[[image:AnalogX_icons.jpg\|640px]]

	~~[[Image:add_to_cart.png\|link=https://www.autosportlabs.com/product/analogx-4-channel-analog-to-can-interface/]]~~

	AnalogX provides 4 buffered and protected 0-5v sensor inputs and can broadcast the sensor values between 1 and 255Hz. It also provides a 0.5A 5v reference for powering sensors.		AnalogX provides 4 buffered and protected 0-5v sensor inputs and can broadcast the sensor values between 1 and 255Hz. It also provides a 0.5A 5v reference for powering sensors.

2020-07-27T19:14:52Z

Troubleshooting

← Older revision		Revision as of 19:14, 27 July 2020
Line 118:		Line 118:
	** Connect the input to AnalogX's ground. Your receiving system should show very close to 0, which is 0 volts.		** Connect the input to AnalogX's ground. Your receiving system should show very close to 0, which is 0 volts.
	** Connect the input to AnalogX's 5v reference. Your receiving system should show very close to 5000, which represents 5000mV.		** Connect the input to AnalogX's 5v reference. Your receiving system should show very close to 5000, which represents 5000mV.

			* '''Note''': The AnalogX inputs are very sensitive and high impedance to prevent affecting the readings of existing circuits. Therefore, if the inputs are disconnected, it will 'float' and may show random readings.

	If you can confirm these readings, then perform the additional steps:		If you can confirm these readings, then perform the additional steps:

2020-07-15T01:36:15Z

Sensor connections

2020-03-24T20:42:12Z

150 PSI pressure sensor

← Older revision		Revision as of 20:42, 24 March 2020
Line 54:		Line 54:
	[[file:linear_temp_sensor_analogx_scaling.png\|480px]]		[[file:linear_temp_sensor_analogx_scaling.png\|480px]]

	===150 PSI pressure sensor===		===10 bar / 150 PSI pressure sensor===
	These common sensors have a range with the following mapping:		These common sensors have a range with the following mapping:

Line 70:		Line 70:

	[[file:AnalogX_150PSI_oil_pressure_example_formula.png\|480px]]		[[file:AnalogX_150PSI_oil_pressure_example_formula.png\|480px]]

			===150 Bar / 2175 PSI pressure sensor===
			Use the formula: '''RAW * 0.5437 - 271.85'''

	===Texense Liquid Temperature Sensor===		===Texense Liquid Temperature Sensor===

2020-01-12T18:00:38Z

Sensor connections

← Older revision		Revision as of 18:00, 12 January 2020
Line 196:		Line 196:

	===Sensor connections===		===Sensor connections===
	Pin 1 is on left when facing connector		Pin 1 is on left when facing board connector
	{\| class="wikitable" \| width="600px"		{\| class="wikitable" \| width="600px"
	\|-		\|-

2020-01-12T18:00:24Z

Power and CAN

← Older revision		Revision as of 18:00, 12 January 2020
Line 171:		Line 171:
	==Wiring==		==Wiring==
	===Power and CAN===		===Power and CAN===
	Pin 1 is on left when facing connector		Pin 1 is on left when facing board connector
	{\| class="wikitable" \| width="600px"		{\| class="wikitable" \| width="600px"
	\|-		\|-

2020-01-12T18:00:01Z

Specifications

← Older revision		Revision as of 18:00, 12 January 2020
Line 150:		Line 150:
	\| 9 - 15volts, protected to 40v (intermittent)		\| 9 - 15volts, protected to 40v (intermittent)
	\|-		\|-
			\| Harness
	\| 26 gauge leads for power, ground, CAN and sensor inputs		\| 26 gauge leads for power, ground, CAN and sensor inputs
	\|-		\|-

2020-01-12T17:59:29Z

Specifications

← Older revision		Revision as of 17:59, 12 January 2020
Line 149:		Line 149:
	\| Power input and connections		\| Power input and connections
	\| 9 - 15volts, protected to 40v (intermittent)		\| 9 - 15volts, protected to 40v (intermittent)
			\|-
	\| 26 gauge leads for power, ground, CAN and sensor inputs		\| 26 gauge leads for power, ground, CAN and sensor inputs
	\|-		\|-

2020-01-12T17:57:32Z

Sensor connections

← Older revision		Revision as of 17:57, 12 January 2020
Line 194:		Line 194:

	===Sensor connections===		===Sensor connections===
			Pin 1 is on left when facing connector
	{\| class="wikitable" \| width="600px"		{\| class="wikitable" \| width="600px"
	\|-		\|-
	! ~~Color~~		! Pin
	! Assignment		! Assignment
	! Notes		! Notes
	\|-		\|-
	\| ~~Brown~~		\| 1
	\| Analog 1 input		\| Analog 1 input
	\| 0-5v input		\| 0-5v input
	\|-		\|-
	\| ~~Pink~~		\| 2
	\| Analog 2 input		\| Analog 2 input
	\| 0-5v input		\| 0-5v input
	\|-		\|-
	\| ~~Purple~~		\| 3
	\| Analog 3 input		\| Analog 3 input
	\| 0-5v input		\| 0-5v input
	\|-		\|-
	\| ~~Blue~~		\| 4
	\| Analog 4 input		\| Analog 4 input
	\| 0-5v input		\| 0-5v input
	\|-		\|-
	\| ~~Yellow~~		\| 5
	\| Voltage reference output (for powering sensors)		\| Voltage reference output (for powering sensors)
	\| 5v @ 0.5A		\| 5v @ 0.5A
	\|-		\|-
	\| ~~Black~~		\| 6
	\| Ground reference		\| Ground reference
	\|		\|

2020-01-12T17:56:44Z

Power and CAN

← Older revision		Revision as of 17:56, 12 January 2020
Line 169:		Line 169:
	==Wiring==		==Wiring==
	===Power and CAN===		===Power and CAN===
			Pin 1 is on left when facing connector
	{\| class="wikitable" \| width="600px"		{\| class="wikitable" \| width="600px"
	\|-		\|-
	! ~~Color~~		! Pin
	! Assignment		! Assignment
	! Notes		! Notes
	\|-		\|-
	\| ~~Red~~		\| 1
	\| 9-15v Power		\| 9-15v Power
	\| Connect this to switched ignition power. 0.25A max consumption.		\| Connect this to switched ignition power. 0.25A max consumption.
	\|-		\|-
	\| ~~Black~~		\| 2
	\| CAN High		\| CAN High
	\|		\|
	\|-		\|-
	\| ~~Orange~~		\| 3
	\| CAN Low		\| CAN Low
	\|		\|
	\|-		\|-
	\| ~~Blue~~		\| 4
	\| Ground		\| Ground
	\|		\|