AnalogX2 - Revision history

Abdurrehman Akhtar: /* CAN bus connection to RaceCapture */

2026-03-07T15:53:52Z

CAN bus connection to RaceCapture

← Older revision		Revision as of 15:53, 7 March 2026
Line 20:		Line 20:

	'''Simple Connection (Single Device)'''		'''Simple Connection (Single Device)'''

	In the simplest configuration, AnalogX2 is connected to the CAN2 branch of the RaceCapture CAN1/CAN2 splitter. An inline CAN terminator is placed at the end of the bus. This configuration is recommended when AnalogX2 is the only CAN device on that branch.		In the simplest configuration, AnalogX2 is connected to the CAN2 branch of the RaceCapture CAN1/CAN2 splitter. An inline CAN terminator is placed at the end of the bus. This configuration is recommended when AnalogX2 is the only CAN device on that branch.

2026-03-07T15:51:52Z

CAN bus connection to RaceCapture

@@ Line 16: / Line 16: @@
 ===CAN bus connection to RaceCapture===
-[[image:analogX_CAN_connection.jpg]]
+AnalogX2 connects directly to the RaceCapture CAN bus using the Autosport Labs plug-and-play harness system.
 {| class="wikitable"

2026-03-03T16:24:44Z

Harness / Cabling

← Older revision		Revision as of 16:24, 3 March 2026
Line 15:		Line 15:
	AnalogX is designed for plug and play connection into Autosport Labs CAN bus networks and sensors. Parts and cables shown are available individually. Refer to the part numbers below to create your own sensor configuration.		AnalogX is designed for plug and play connection into Autosport Labs CAN bus networks and sensors. Parts and cables shown are available individually. Refer to the part numbers below to create your own sensor configuration.

	====CAN bus connection to RaceCapture====		===CAN bus connection to RaceCapture===
	[[image:analogX_CAN_connection.jpg]]		[[image:analogX_CAN_connection.jpg]]

Line 27:		Line 27:
	\|}		\|}

	====Sensor Connections====		===Sensor Connections===
	[[image:analogX_plug_and_play_sensors.jpg]]		[[image:analogX_plug_and_play_sensors.jpg]]

2024-09-17T16:12:48Z

No CAN data

← Older revision		Revision as of 16:12, 17 September 2024
Line 219:		Line 219:

	===No CAN data===		===No CAN data===
			* Ensure AnalogX is receiving 12v via it's connection.
			** '''Note''': Ensure your data system is also receiving 12v if it is powering AnalogX
	* Double check the CAN bus connections		* Double check the CAN bus connections
	* Verify the CAN baud rate is compatible with the AnalogX configuration (1M by default, 500K enabled with DIP switch)		* Verify the CAN baud rate is compatible with the AnalogX configuration (1M by default, 500K enabled with DIP switch)

2024-03-05T16:52:28Z

10 bar / 150 PSI pressure sensor

← Older revision		Revision as of 16:52, 5 March 2024
Line 109:		Line 109:
	for 0-150 PSI use the formula: '''RAW * 0.0375 - 18.75'''		for 0-150 PSI use the formula: '''RAW * 0.0375 - 18.75'''

	* '''Note:''': The 0.~~375~~ value was derived from the formua: 150 PSI / 4000mV = 0.0375 PSI/mV		* '''Note:''': The 0.0375 value was derived from the formua: 150 PSI / 4000mV = 0.0375 PSI/mV

	[[file:AnalogX_150PSI_oil_pressure_example_formula.png\|480px]]		[[file:AnalogX_150PSI_oil_pressure_example_formula.png\|480px]]

2023-01-07T21:02:38Z

CAN Messages

2021-03-01T21:40:58Z

Configuration Group 1

← Older revision		Revision as of 21:40, 1 March 2021
Line 386:		Line 386:
	Configures options for AnalogX.		Configures options for AnalogX.

	Send this message to AnalogX to configure runtime settings. Settings are preserved across power cycles.		Send this message to AnalogX to configure runtime settings. Settings are saved in flash memory and will be preserved across power cycles.

	* '''Note:''' To read the current settings, broadcast a message with this CAN ID with no data (data length of 0) - AnalogX will reply with the current configuration.		* '''Note:''' To read the current settings, broadcast a message with this CAN ID with no data (data length of 0) - AnalogX will reply with the current configuration.

2021-03-01T21:40:02Z

Configuration Group 1

← Older revision		Revision as of 21:40, 1 March 2021
Line 386:		Line 386:
	Configures options for AnalogX.		Configures options for AnalogX.

	Send this message to AnalogX to configure runtime settings.		Send this message to AnalogX to configure runtime settings. Settings are preserved across power cycles.

	* '''Note:''' ~~Settings are volatile and are not persisted across power cycles~~.		* '''Note:''' To read the current settings, broadcast a message with this CAN ID with no data (data length of 0) - AnalogX will reply with the current configuration.

	====Address====		====Address====

2021-03-01T21:38:49Z

Address

2021-01-22T19:27:15Z

Specifications