Hondata KPro4 - Revision history

Sbarton: /* CAN preset */

2021-01-06T14:17:09Z

CAN preset

← Older revision		Revision as of 14:17, 6 January 2021
Line 36:		Line 36:

	Under CAN Bus, select 500Kbps for the baud rate and Termination On.		Under CAN Bus, select 500Kbps for the baud rate and Termination On.
			[[image:CANBUSBaudRate.png]]

	~~[[image:CANBUSBaudRate.png]]~~

	Under RaceCapture / CAN channels Setup, select the Hondata preset from the list of presets available.		Under RaceCapture / CAN channels Setup, select the Hondata preset from the list of presets available.

	[[image:Hondata_CAN_preset.png]]		[[image:Hondata_CAN_preset.png]]

Sbarton: /* CAN preset */

2021-01-06T14:16:18Z

CAN preset

← Older revision		Revision as of 14:16, 6 January 2021
Line 34:		Line 34:

	==CAN preset==		==CAN preset==

			Under CAN Bus, select 500Kbps for the baud rate and Termination On.

			[[image:CANBUSBaudRate.png]]

	Under RaceCapture / CAN channels Setup, select the Hondata preset from the list of presets available.		Under RaceCapture / CAN channels Setup, select the Hondata preset from the list of presets available.

	[[image:Hondata_CAN_preset.png]]		[[image:Hondata_CAN_preset.png]]


	After selecting the preset, write the settings back to RaceCapture		After selecting the preset, write the settings back to RaceCapture

Brentp: /* Wiring */

2020-05-12T19:56:00Z

Wiring

← Older revision		Revision as of 19:56, 12 May 2020
Line 22:		Line 22:

	* '''CAN1 High''' from RaceCapture to '''CAN high''' of the Hondata system.		* '''CAN1 High''' from RaceCapture to '''CAN high''' of the Hondata system.
	* '''~~CAN2~~ Low''' from RaceCapture to '''CAN low''' of the Hondata system.		* '''CAN1 Low''' from RaceCapture to '''CAN low''' of the Hondata system.

	For RaceCapture wiring, see the [[CAN_Bus_Integration\|CAN integration guide]] for wiring details.		For RaceCapture wiring, see the [[CAN_Bus_Integration\|CAN integration guide]] for wiring details.

Brentp: /* Wiring */

2018-11-16T22:59:22Z

Wiring

← Older revision		Revision as of 22:59, 16 November 2018
Line 24:		Line 24:
	* '''CAN2 Low''' from RaceCapture to '''CAN low''' of the Hondata system.		* '''CAN2 Low''' from RaceCapture to '''CAN low''' of the Hondata system.

	For RaceCapture wiring, see the [CAN_Bus_Integration\|CAN integration guide]] for wiring details.		For RaceCapture wiring, see the [[CAN_Bus_Integration\|CAN integration guide]] for wiring details.

	'''Note:''' Ensure RaceCapture and the Hondata system are grounded to a common location to prevent CAN bus data errors.		'''Note:''' Ensure RaceCapture and the Hondata system are grounded to a common location to prevent CAN bus data errors.

Brentp at 22:38, 16 November 2018

2018-11-16T22:38:38Z

@@ Line 19: / Line 19: @@
 ==Wiring==
-Use the supplied Hondata harness and connect the CAN High / CAN Low to the corresponding CAN High / CAN Low on the RaceCapture/Pro CAN 1 channel. See the [CAN_Bus_Integration|CAN integration guide]] for wiring details.
+Connecting to the Hondata system requires two wires:
-==CAN termination==
+* '''CAN1 High''' from RaceCapture  to '''CAN high''' of the Hondata system.
-The KPro4 does not have built-in CAN termination. You will need to also connect a 120 ohm resistor across the CAN High / CAN Low connections at the connections to the KPro4.
+* '''CAN2 Low''' from RaceCapture  to '''CAN low''' of the Hondata system.
-=Script=
+For RaceCapture wiring, see the [CAN_Bus_Integration|CAN integration guide]] for wiring details.
-<pre>
+'''Note:''' Ensure RaceCapture and the Hondata system are grounded to a common location to prevent CAN bus data errors.
-tickRate = 30
+If you are unsure about how to wire the Hondata ECU, or what connections to use, please contact [https://www.hondata.com/ Hondata] for support.
---add your virtual channels here
+==CAN termination==
-rpmId = addChannel("RPM", 25, 0, 0, 9000, "RPM")
+The KPro4 does not have built-in CAN termination. You will need to also connect a 120 ohm resistor across the CAN High / CAN Low connections at the connections to the KPro4.
-function onTick()
+==CAN preset==
-function processLogging()
+Under RaceCapture / CAN channels Setup, select the Hondata preset from the list of presets available.
---===========do not edit below===========
+After selecting the preset, write the settings back to RaceCapture
---Map CAN channel, big endian format
+==Verifying Data==
-initCAN(CAN_chan, CAN_baud)
+Switch to the Dashboard mode, then page to the raw channels view.  You should see your Hondata channels updating in real time.

Brentp at 09:54, 21 December 2016

2016-12-21T09:54:50Z

← Older revision		Revision as of 09:54, 21 December 2016
Line 1:		Line 1:
	=Introduction=		=Introduction=
	The following script adapts the Hondata ~~KPro4~~ CAN to RaceCapture/Pro		The following script adapts the Hondata CAN to RaceCapture/Pro. KPro4 and S300 CAN are supported.

	[[Image:Hondata_KPro4.jpg]]		[[Image:Hondata_KPro4.jpg]]

Brentp: /* Script */

2016-07-20T16:12:53Z

Script

← Older revision		Revision as of 16:12, 20 July 2016
Line 30:		Line 30:
	--This example adopted to Hondata KPro4 CAN output		--This example adopted to Hondata KPro4 CAN output

	~~--how frequently we poll for CAN messages, 30Hz is the max~~
	tickRate = 30		tickRate = 30
	--the CAN baud rate		--the CAN baud rate

Brentp: enhanced instructions

2016-07-20T16:12:32Z

enhanced instructions

@@ Line 1: / Line 1: @@
 The following script adapts the Hondata KPro4 CAN to RaceCapture/Pro
 [[Image:Hondata_KPro4.jpg]]
 <pre>

Brentp at 16:57, 14 May 2016

2016-05-14T16:57:07Z

← Older revision		Revision as of 16:57, 14 May 2016
Line 50:		Line 50:
	function onTick()		function onTick()
	processCAN(CAN_chan)		processCAN(CAN_chan)
	--processLogging()		processLogging()
	end		end

Brentp: added PSI conversion to MAP channel

2016-04-30T20:04:07Z

added PSI conversion to MAP channel

← Older revision		Revision as of 20:04, 30 April 2016
Line 16:		Line 16:
	rpmId = addChannel("RPM", 25, 0, 0, 9000, "RPM")		rpmId = addChannel("RPM", 25, 0, 0, 9000, "RPM")
	vltId = addChannel("EcuVolts", 10, 1, 0, 20, "volts")		vltId = addChannel("EcuVolts", 10, 1, 0, 20, "volts")
	iatId = addChannel("IAT", 1, 0, 0, 100, "C")		iatId = addChannel("IAT", 1, 0, 0, 100, "F")
	ectId = addChannel("EngineTemp", 1, 0, 0, 150, "C")		ectId = addChannel("EngineTemp", 1, 0, 0, 150, "F")
	tpsId = addChannel("TPS", 10, 0, 0, 100, "%")		tpsId = addChannel("TPS", 10, 0, 0, 100, "%")
	mapId = addChannel("MAP", 10, 1, 0, 15, "PSI")		mapId = addChannel("MAP", 10, 2, -15, 25, "PSI")
	injId = addChannel("InjectorPW", 10, 3, 0, 100, "ms")		injId = addChannel("InjectorPW", 10, 3, 0, 100, "ms")
	ignId = addChannel("Ignition", 10, 0, -20, 20, "D")		ignId = addChannel("Ignition", 10, 0, -20, 20, "D")
Line 41:		Line 41:
	[1632] = function(data) map_chan(rpmId, data, 0, 2, 1, 0) map_chan(vltId, data, 5, 1, 0.1, 0) end,		[1632] = function(data) map_chan(rpmId, data, 0, 2, 1, 0) map_chan(vltId, data, 5, 1, 0.1, 0) end,
	[1633] = function(data) map_chan(iatId, data, 0, 2, 1, 0, toF) map_chan(ectId, data, 2, 2, 1, 0, toF) end,		[1633] = function(data) map_chan(iatId, data, 0, 2, 1, 0, toF) map_chan(ectId, data, 2, 2, 1, 0, toF) end,
	[1634] = function(data) map_chan(tpsId, data, 0, 2, 1, 0) map_chan(mapId, data, 2, 2, 0.0145037738, 0) end,		[1634] = function(data) map_chan(tpsId, data, 0, 2, 1, 0) map_chan(mapId, data, 2, 2, 0.0145037738, -14.7) end,
	[1635] = function(data) map_chan(injId, data, 0, 2, 0.001, 0) map_chan(ignId, data, 2, 2, 1, 0) end,		[1635] = function(data) map_chan(injId, data, 0, 2, 0.001, 0) map_chan(ignId, data, 2, 2, 1, 0) end,
	[1636] = function(data) map_chan(lmdId, data, 0, 2, 0.00003051757, 0, toAFR) end,		[1636] = function(data) map_chan(lmdId, data, 0, 2, 0.00003051757, 0, toAFR) end,
Line 91:		Line 91:
	initCAN(CAN_chan, CAN_baud)		initCAN(CAN_chan, CAN_baud)
	setTickRate(tickRate)		setTickRate(tickRate)


	</pre>		</pre>