Multiple CAN Systems - Revision history

Sbarton at 19:50, 5 January 2021

2021-01-05T19:50:24Z

← Older revision		Revision as of 19:50, 5 January 2021
Line 1:		Line 1:
			- Written by [https://www.facebook.com/scott.barton.76 Scott Barton] of [https://www.facebook.com/ProFormanceCoachingcom ProFormance Coaching]

	You can integrate multiple CAN systems into your Race Capture or Podium Connect devices. You may be able to add some of them on the same CAN Channel or you may need to put them on different CAN Channels. Each ASL device has 2 CAN Bus Channels available to connect your CAN systems to. CAN systems that operate at different baud rates CANNOT be on the same CAN Channel. Some systems that operate at the same baud rate may interfere with each other so those might need to be on different CAN channels.		You can integrate multiple CAN systems into your Race Capture or Podium Connect devices. You may be able to add some of them on the same CAN Channel or you may need to put them on different CAN Channels. Each ASL device has 2 CAN Bus Channels available to connect your CAN systems to. CAN systems that operate at different baud rates CANNOT be on the same CAN Channel. Some systems that operate at the same baud rate may interfere with each other so those might need to be on different CAN channels.

Sbarton: /* RJ45 Splitter */

2020-02-21T17:53:54Z

RJ45 Splitter

← Older revision		Revision as of 17:53, 21 February 2020
Line 24:		Line 24:

	==RJ45 Splitter==		==RJ45 Splitter==
	If you already have a CAN system using an RJ45 plug with your Race Capture device, you may need an [https://amzn.to/~~2ur2TiT~~ RJ45 splitter like this $10 one].		If you already have a CAN system using an RJ45 plug with your Race Capture device, you may need an [https://amzn.to/37NtHLN RJ45 splitter like this $10 one].

	Most of ASL's CAN cables are wired to CAN 1. Note that if the devices are all wired to CAN1 on their RJ45 cables, they will all need to operate at the same baud rate. If they operate at different baud rates or interfere with each other, you would need to use a [[CAN_Crossover_Cable\|RJ45 CAN Crossover Cable]] in that case to move that device from CAN1 to CAN2 (see below).		Most of ASL's CAN cables are wired to CAN 1. Note that if the devices are all wired to CAN1 on their RJ45 cables, they will all need to operate at the same baud rate. If they operate at different baud rates or interfere with each other, you would need to use a [[CAN_Crossover_Cable\|RJ45 CAN Crossover Cable]] in that case to move that device from CAN1 to CAN2 (see below).

	[[Image:RJ45_Splitter.jpg\|500px\|link=https://amzn.to/~~2ur2TiT~~]]		[[Image:RJ45_Splitter.jpg\|500px\|link=https://amzn.to/37NtHLN]]

	==Custom RJ45 CAN Cross Over Adapter==		==Custom RJ45 CAN Cross Over Adapter==

Sbarton at 22:04, 18 July 2019

2019-07-18T22:04:25Z

← Older revision		Revision as of 22:04, 18 July 2019
Line 1:		Line 1:
	You can integrate multiple CAN systems into your Race Capture or Podium Connect devices. You may be able to add some of them on the same CAN Channel or you may need to put them on different CAN Channels. Each ASL device has 2 CAN Bus Channels available to connect your CAN systems ~~too~~. CAN systems that operate at different baud rates CANNOT be on the same CAN Channel. Some systems that operate at the same baud rate may interfere with each other so those might need to be on different CAN channels.		You can integrate multiple CAN systems into your Race Capture or Podium Connect devices. You may be able to add some of them on the same CAN Channel or you may need to put them on different CAN Channels. Each ASL device has 2 CAN Bus Channels available to connect your CAN systems to. CAN systems that operate at different baud rates CANNOT be on the same CAN Channel. Some systems that operate at the same baud rate may interfere with each other so those might need to be on different CAN channels.

	[[Image:AIM_TPMS_OBDII_Data.png\|600px]]		[[Image:AIM_TPMS_OBDII_Data.png\|600px]]

Sbarton: /* RJ45 Splitter */

2019-05-30T16:20:13Z

RJ45 Splitter

← Older revision		Revision as of 16:20, 30 May 2019
Line 26:		Line 26:
	If you already have a CAN system using an RJ45 plug with your Race Capture device, you may need an [https://amzn.to/2ur2TiT RJ45 splitter like this $10 one].		If you already have a CAN system using an RJ45 plug with your Race Capture device, you may need an [https://amzn.to/2ur2TiT RJ45 splitter like this $10 one].

	Most of ASL's CAN cables are wired to CAN 1. Note that if the devices are all wired to CAN1 on their RJ45 cables, they will all need to operate at the same baud rate. If they operate at different baud rates or interfere with each other, you would need to use a [[CAN_Crossover_Cable\|RJ45 CAN Crossover Cable]] in that case to move that device from CAN1 to CAN2.		Most of ASL's CAN cables are wired to CAN 1. Note that if the devices are all wired to CAN1 on their RJ45 cables, they will all need to operate at the same baud rate. If they operate at different baud rates or interfere with each other, you would need to use a [[CAN_Crossover_Cable\|RJ45 CAN Crossover Cable]] in that case to move that device from CAN1 to CAN2 (see below).

	[[Image:RJ45_Splitter.jpg\|500px\|link=https://amzn.to/2ur2TiT]]		[[Image:RJ45_Splitter.jpg\|500px\|link=https://amzn.to/2ur2TiT]]

Sbarton: /* NOTES: */

2019-05-30T16:18:59Z

NOTES:

← Older revision		Revision as of 16:18, 30 May 2019
Line 38:		Line 38:

	==NOTES:==		==NOTES:==
	Most of ASL's CAN cables are wired to CAN1.		Most of ASL's CAN cables are wired to CAN1 on the RJ45 plug.

	If you wire a device to CAN bus 2 and that device has a Preset, you may have to go into each channel and change it from CAN Bus 1 to CAN Bus 2.		If you wire a device to CAN bus 2 and that device has a Preset, you may have to go into each channel and change it from CAN Bus 1 to CAN Bus 2.

	[[Image:RC_CANBus.jpg\|500px\|link=AIM_Integration_CAN_Mapping#8.29_Click_.2B_Button_to_add_a_New_Channel]]		[[Image:RC_CANBus.jpg\|500px\|link=AIM_Integration_CAN_Mapping#8.29_Click_.2B_Button_to_add_a_New_Channel]]

Sbarton: /* NOTES: */

2019-05-30T16:18:45Z

NOTES:

← Older revision		Revision as of 16:18, 30 May 2019
Line 38:		Line 38:

	==NOTES:==		==NOTES:==
			Most of ASL's CAN cables are wired to CAN1.
	If you wire a device to CAN bus 2 and that device has a Preset, you may have to go into each channel and change it from CAN Bus 1 to CAN Bus 2.		If you wire a device to CAN bus 2 and that device has a Preset, you may have to go into each channel and change it from CAN Bus 1 to CAN Bus 2.

	[[Image:RC_CANBus.jpg\|500px\|link=AIM_Integration_CAN_Mapping#8.29_Click_.2B_Button_to_add_a_New_Channel]]		[[Image:RC_CANBus.jpg\|500px\|link=AIM_Integration_CAN_Mapping#8.29_Click_.2B_Button_to_add_a_New_Channel]]

Sbarton: /* Custom RJ45 CAN Cross Over Adapter to move a device wired to CAN 1 on an RJ45 cable to CAN2 or vice versa. */

2019-05-30T16:13:39Z

Custom RJ45 CAN Cross Over Adapter to move a device wired to CAN 1 on an RJ45 cable to CAN2 or vice versa.

← Older revision		Revision as of 16:13, 30 May 2019
Line 32:		Line 32:
	==Custom RJ45 CAN Cross Over Adapter==		==Custom RJ45 CAN Cross Over Adapter==
	=====Custom RJ45 CAN Cross Over Adapter to move a device wired to CAN 1 on an RJ45 cable to CAN2 or vice versa.=====		=====Custom RJ45 CAN Cross Over Adapter to move a device wired to CAN 1 on an RJ45 cable to CAN2 or vice versa.=====
	If you have a CAN device/system that is already wired to CAN 1 on an RJ45 cable, you may need to move that to CAN 2. This may be because your CAN systems operate at 2 different baud rates or it may be that they interfere with each other, or you may just want to separate the 2 CAN systems. You can do this by creating a custom [https://wiki.autosportlabs.com/CAN_Crossover_Cable CAN CrossOver cable] that will swap the CAN1 and CAN2 wire pairs. Please see this link for full info on how to do that.		If you have a CAN device/system that is already wired to CAN 1 on an RJ45 cable, you may need to move that to CAN 2 (most of ASL's CAN cables are wired to CAN1). This may be because your CAN systems operate at 2 different baud rates or it may be that they interfere with each other, or you may just want to separate the 2 CAN systems. You can do this by creating a custom [https://wiki.autosportlabs.com/CAN_Crossover_Cable CAN CrossOver cable] that will swap the CAN1 and CAN2 wire pairs. Please see this link for full info on how to do that.
	https://wiki.autosportlabs.com/CAN_Crossover_Cable		https://wiki.autosportlabs.com/CAN_Crossover_Cable

Sbarton: /* RJ45 Splitter */

2019-05-30T16:12:47Z

RJ45 Splitter

← Older revision		Revision as of 16:12, 30 May 2019
Line 26:		Line 26:
	If you already have a CAN system using an RJ45 plug with your Race Capture device, you may need an [https://amzn.to/2ur2TiT RJ45 splitter like this $10 one].		If you already have a CAN system using an RJ45 plug with your Race Capture device, you may need an [https://amzn.to/2ur2TiT RJ45 splitter like this $10 one].

	Note that if the devices are all wired to CAN1 on their RJ45 cables, they will all need to operate at the same baud rate. If they operate at different baud rates or interfere with each other, you would need to use a [[CAN_Crossover_Cable\|RJ45 CAN Crossover Cable]] in that case to move that device from CAN1 to CAN2.		Most of ASL's CAN cables are wired to CAN 1. Note that if the devices are all wired to CAN1 on their RJ45 cables, they will all need to operate at the same baud rate. If they operate at different baud rates or interfere with each other, you would need to use a [[CAN_Crossover_Cable\|RJ45 CAN Crossover Cable]] in that case to move that device from CAN1 to CAN2.

	[[Image:RJ45_Splitter.jpg\|500px\|link=https://amzn.to/2ur2TiT]]		[[Image:RJ45_Splitter.jpg\|500px\|link=https://amzn.to/2ur2TiT]]

Sbarton: /* Custom RJ45 CAN Cross Over Adapter */

2019-05-29T20:21:15Z

Custom RJ45 CAN Cross Over Adapter

← Older revision		Revision as of 20:21, 29 May 2019
Line 35:		Line 35:
	https://wiki.autosportlabs.com/CAN_Crossover_Cable		https://wiki.autosportlabs.com/CAN_Crossover_Cable

	[[Image:CANXOverAdapter.jpg\|600px\|link=CAN_Crossover_Cable ~~CAN CrossOver~~]]		[[Image:CANXOverAdapter.jpg\|600px\|link=CAN_Crossover_Cable]]

	==NOTES:==		==NOTES:==

Sbarton: /* Custom RJ45 CAN Cross Over Adapter */

2019-05-29T20:20:56Z

Custom RJ45 CAN Cross Over Adapter

← Older revision		Revision as of 20:20, 29 May 2019
Line 35:		Line 35:
	https://wiki.autosportlabs.com/CAN_Crossover_Cable		https://wiki.autosportlabs.com/CAN_Crossover_Cable

	[[Image:CANXOverAdapter.jpg\|600px\|link=~~https://wiki.autosportlabs.com/~~CAN_Crossover_Cable CAN CrossOver]]		[[Image:CANXOverAdapter.jpg\|600px\|link=CAN_Crossover_Cable CAN CrossOver]]

	==NOTES:==		==NOTES:==