RacecaptureApex hardware install - Revision history

Brentp: /* Cellular Telemetry */

2018-04-04T23:07:50Z

Cellular Telemetry

← Older revision		Revision as of 23:07, 4 April 2018
Line 132:		Line 132:
	If optioned with the 3.5G real-time cellular telemetry module, connect the cellular antenna to this port.		If optioned with the 3.5G real-time cellular telemetry module, connect the cellular antenna to this port.
	* '''Note:''' Tighten this connection to '''5-6 inch/lbs''' (just beyond finger tight). '''Do not over torque'''		* '''Note:''' Tighten this connection to '''5-6 inch/lbs''' (just beyond finger tight). '''Do not over torque'''
			===SIM card installation===
			RaceCapture/Apex requires a micro SIM from a GSM provider, such as AT&T, T-Mobile, FreedomPop, or many other worldwide providers.

			Install the micro SIM in the card slot behind the rubber flap at the rear of the unit. The SIM fits in the bottom position of the card holder; the Micro SD installs in the top position.

			* '''More Info:;''' See the [[RaceCapture_real_time_telemetry\|Real-time telemetry guide]] for additional setup instructions

	==Antenna Placement Guide==		==Antenna Placement Guide==

Brentp: /* Guides */

2017-05-11T04:53:09Z

Guides

← Older revision		Revision as of 04:53, 11 May 2017
Line 191:		Line 191:

	===Guides===		===Guides===
	* See our comprehensive [[RaceCapturePro_Sensors Sensor Guide]] for information on connecting various types of analog sensors.		* See our comprehensive [[RaceCapturePro_Sensors\|Sensor Guide]] for information on connecting various types of analog sensors.
	* Also see our guide on [[RaceCapturePro_Calibrate_Sensor\|Calibrating an Analog Sensor]]		* Also see our guide on [[RaceCapturePro_Calibrate_Sensor\|Calibrating an Analog Sensor]]

Brentp at 04:52, 11 May 2017

2017-05-11T04:52:43Z

← Older revision		Revision as of 04:52, 11 May 2017
Line 18:		Line 18:

	==Main Connector==		==Main Connector==
	The main connector provides access to all power, sensor and communications for the RaceCapture/~~Pro~~ system.		The main connector provides access to all power, sensor and communications for the RaceCapture/Apex system.

	[[file:RaceCaptureApex_pinout.png\|700px]]		[[file:RaceCaptureApex_pinout.png\|700px]]

	{\| class="wikitable" style="text-align:center; width:700px; height:200px;"		{\| class="wikitable" style="text-align:center; width:700px; height:200px;"
	\|+ RaceCapture/~~Pro MK3~~ connector pinout		\|+ RaceCapture/Apex connector pinout
	\|-		\|-
	! colspan="2" \| Power		! colspan="2" \| Power
Line 146:		Line 146:

	=Powering=		=Powering=
	Connect RaceCapture/~~Pro~~ to a 12v source, ideally switched with main power or via ignition power.		Connect RaceCapture/Apex to a 12v source, ideally switched with main power or via ignition power.

	[[file:RaceCaptureApex_power_pinout.png\|700px]]		[[file:RaceCaptureApex_power_pinout.png\|700px]]
Line 195:		Line 195:

	==Frequency / RPM sensor input==		==Frequency / RPM sensor input==
	You can connect RPM, wheel speed and other pulse-type sensors to RaceCapture/~~Pro~~ frequency input pins.		You can connect RPM, wheel speed and other pulse-type sensors to RaceCapture/Apex frequency input pins.

	{\| class="wikitable" style="text-align:center; width:700px; height:200px;"		{\| class="wikitable" style="text-align:center; width:700px; height:200px;"
Line 233:		Line 233:

	==GPIO==		==GPIO==
	RaceCapture/~~Pro~~ provides 3 General Purpose Input Output (GPIO) ports which you can use to control devices (Output mode) or read switches or high / low states of electrical signals.		RaceCapture/Apex provides 3 General Purpose Input Output (GPIO) ports which you can use to control devices (Output mode) or read switches or high / low states of electrical signals.

	===Specifications===		===Specifications===
Line 253:		Line 253:

	===Input Mode===		===Input Mode===
	When configured for input mode, the RaceCapture/~~Pro~~ sensor input will register a '1' when the input passes a voltage threshold of approximately 3v, and '0' when the input is low (close to 0 volts).		When configured for input mode, the RaceCapture/Apex sensor input will register a '1' when the input passes a voltage threshold of approximately 3v, and '0' when the input is low (close to 0 volts).

	'''Important Note:''' when sensing large inductive loads, such as sensing brake light state or sensing the on/off state of a motor, connect a '''10K 1/4 watt resistor''' in-line with the GPIO input to protect RaceCapture/~~Pro~~ from a large inductive spike.		'''Important Note:''' when sensing large inductive loads, such as sensing brake light state or sensing the on/off state of a motor, connect a '''10K 1/4 watt resistor''' in-line with the GPIO input to protect RaceCapture/Apex from a large inductive spike.

	===Output Mode===		===Output Mode===

Brentp: Created page with "=Installation= ==Mounting Orientation== The default and recommended mounting orientation is flat with indicators facing forward for visibility. !!mounting orientation pic..."

2017-05-11T04:51:39Z

Created page with "=Installation= ==Mounting Orientation== The default and recommended mounting orientation is flat with indicators facing forward for visibility. !!mounting orientation pic..."

New page

=Installation=

==Mounting Orientation==
The default and recommended mounting orientation is flat with indicators facing forward for visibility.

!!mounting orientation pic

* Mount as flat as possible for best performance from the built-in accelerometer / gyro.

===Alternative Mounting===
You can mount the system in other orientations. For best accelerometer and gyro performance, it's recommended you mount in an orientation that's square to the orientation of the car.
* Example:
** Upside down
** Vertical / on edge
If an alternate mounting orientation is chosen, you should re-map the accelerometer and gyro channels to reflect this change.

=Connections=

==Main Connector==
The main connector provides access to all power, sensor and communications for the RaceCapture/Pro system.

[[file:RaceCaptureApex_pinout.png|700px]]

{| class="wikitable" style="text-align:center; width:700px; height:200px;"
|+ RaceCapture/Pro MK3 connector pinout
|-
! colspan="2" | Power

|-
! Connection
! Color
|-
| 12v
| Red
|-
| Ground
| Black
|-
! colspan="2" | Frequency / RPM sensor inputs
|-
| Blue
| Frequency / RPM input 1
|-
| Blue / White stripe
| Frequency / RPM input 2
|-
| Blue / Green Stripe
| Frequency / RPM input 3
|-
| Blue / Orange Stripe
| Frequency / RPM input 4
|-
! colspan="2" | Voltage Reference
|-
| Yellow
| +5v reference
|-
! colspan="2" | Analog Sensor Inputs
|-
| White
| Analog Input 1
|-
| White / Black Stripe
| Analog Input 2
|-
| White / Orange Stripe
| Analog Input 3
|-
| White / Blue Stripe
| Analog Input 4
|-
| White / Gray Stripe
| Analog Input 5
|-
| White / Green Stripe
| Analog Input 6
|-
| White / Red Stripe
| Analog Input 7
|-
| White / Brown Stripe
| Analog Input 8
|-
! colspan="2" | General Purpose Input / Output (GPIO)
|-
| Gray
| GPIO 1
|-
| Gray / White Stripe
| GPIO 2
|-
| Gray / Blue Stripe
| GPIO 3
|-
! colspan="2" | Auxiliary Serial Input
|-
| Purple / White Stripe
| Auxiliary RS232 Serial TX
|-
| Purple
| Auxiliary RS232 Serial RX
|-
! colspan="2" | CAN Bus

|-
| Orange / Blue Stripe
| CAN 1 High
|-
| Orange
| CAN 1 Low
|-
| Orange / Green Stripe
| CAN 2 High
|-
| Orange / White Stripe
| CAN 1 Low
|}

===Plug Connector Type===
The standard Deutsch DTM connector system is used:

* DTM06-12SA
* DTM06-12SB
* Matching wedge lock (WM-12S)
* Pins 0462-201-20141

==GPS==
Connect the included GPS antenna to this port.
* '''Note:''' Tighten this connection to '''5-6 inch/lbs''' (just beyond finger tight). '''Do not over torque'''

==Cellular Telemetry==
If optioned with the 3.5G real-time cellular telemetry module, connect the cellular antenna to this port.
* '''Note:''' Tighten this connection to '''5-6 inch/lbs''' (just beyond finger tight). '''Do not over torque'''

==Antenna Placement Guide==
===GPS===
For optimal GPS reception, install GPS antenna with a clear 360 degree view of the sky, such as on the roof of the vehicle.

===Cellular antenna===
For optimal cellular performance, install the cellular antenna on the roof of the vehicle, using the roof as a ground plane.

===Antenna separation===
It's recommended you separate the GPS and cellular antennas as reasonably far apart as possible, such as mounting at opposite ends of the roof.
[[file:RaceCapture_Pro_MK3_antenna_install.png]]
* '''Note:''' - about 3 foot / 1 meter separation is ideal.

=Powering=
Connect RaceCapture/Pro to a 12v source, ideally switched with main power or via ignition power.

[[file:RaceCaptureApex_power_pinout.png|700px]]

==Power requirements==
{| class="wikitable" style="text-align:center; width:700px; height:100px;"
|+ Power requirements
|-
| Voltage
| 12-24v
|-
| Fused circuit
| 5A max
|}

=Sensors=
==Analog Sensor inputs==
9 analog sensor input channels are provided: 8 are available for dedicated sensors, plus a 9th internal channel assigned to battery voltage.
{| class="wikitable" style="text-align:center; width:700px; height:200px;"
|+ Analog channel specifications
|-
| Voltage Range
| 0-5v
|-
| Input Impedance
| Greater than 1M ohm
|-
| Voltage protection
| 400v (intermittent)
|-
| ADC precision
| 12 bit SAR
|-
| Maximum Sample Rate
| 1000Hz (logging to SD card)
|-
| Mapping supported
| Raw voltage / linear formula / interpolated map
|}
===Connecting Sensors===
Connect each analog sensor to the respective analog sensor input on the main connector.

[[file:RaceCaptureApex_analog_pinout.png|700px]]

===Guides===
* See our comprehensive [[RaceCapturePro_Sensors Sensor Guide]] for information on connecting various types of analog sensors.
* Also see our guide on [[RaceCapturePro_Calibrate_Sensor|Calibrating an Analog Sensor]]

==Frequency / RPM sensor input==
You can connect RPM, wheel speed and other pulse-type sensors to RaceCapture/Pro frequency input pins.

{| class="wikitable" style="text-align:center; width:700px; height:200px;"
|+ Frequency channel specifications
|-
| Voltage Range
| 0-12v
|-
| Input Impedance
| Greater than 1M ohm
|-
| Voltage protection
| 400v (intermittent)
|-
| Maximum Sample Rate
| 1000Hz (logging to SD card)
|-
| Mapping supported
| RPM / Frequency / Period
|}

===Signal input quality===
Verify the source provides a relatively clean, pulse signal that transitions between 0 and 5-12 volts.

===Special note about RPM inputs===
For best performance and reliability, it's preferred to obtain a clean RPM signal from the engine's ECU.
* Verify if the signal you're tapping is driving the ignition coil directly, or if it's feeding into an igniter. If it's powering the coil directly, use the [[CoilX]] module to buffer / filter the high voltage signal.
* If uncertain, visualize the RPM signal using an oscilloscope - you should see a relatively clean square wave as the source.
* If your only source for RPM is the trigger wire driving the ignition coil primary winding, then you will need the [[CoilX]] module to buffer / filter the noisy, high-voltage component.

==Connecting Sensors==
Connect each sensor connection to the respective frequency sensor input on the main connector.

[[file:RaceCaptureApex_timer_pinout.png|700px]]

See our [[RaceCapturePro_RPM|RPM connection guide]] for more information connecting and calibrating these frequency / RPM channels.

==GPIO==
RaceCapture/Pro provides 3 General Purpose Input Output (GPIO) ports which you can use to control devices (Output mode) or read switches or high / low states of electrical signals.

===Specifications===
{| class="wikitable" style="text-align:center; width:700px; height:200px;"
|+ GPIO channel specifications
|-
| Output mode type
| Open Drain (connects ground when activated)
|-
| Output current capacity
| 1A, inductively clamped
|-
| Input mode voltage range
| 0-12v
|-
| Input voltage protection
| 0-40v - inductive protection up to 1A
|}

===Input Mode===
When configured for input mode, the RaceCapture/Pro sensor input will register a '1' when the input passes a voltage threshold of approximately 3v, and '0' when the input is low (close to 0 volts).

'''Important Note:''' when sensing large inductive loads, such as sensing brake light state or sensing the on/off state of a motor, connect a '''10K 1/4 watt resistor''' in-line with the GPIO input to protect RaceCapture/Pro from a large inductive spike.

===Output Mode===
When configured for output mode, RaceCapture can drive a 1A load per port, suitable for driving indicators, relays, sending signals to other systems and driving small devices.

====Output Behaviour====
* When the port is active, the port will connect to ground.
* When the port is inactive, the port will be an open circuit.

===GPIO Connections===
[[file:RaceCaptureApex_gpio_pinout.png|700px]]

===Controlling GPIO Ports===
GPIO channels in output mode are controlled by the logic you create with the on-board Lua scripting capability.

* See the [[RaceCapturePro_Lua_Scripting#General_Input_.2F_Output_.28GPIO.29_Functions|GPIO section of the Lua Scripting reference]] and collection of [[RaceCapturePro_Lua_Scripting_Examples|Examples]].

=Communications=
==CAN Channels 1 / 2==
Two CAN channels are provided on the main connector as well as on the RJ45 connector.

See the [[RCP_CAN|CAN bus / ECU integration guide]] for information on integrating CAN bus communications and CAN channel mapping

{| class="wikitable" style="text-align:center; width:700px; height:200px;"
|+ CAN channel specifications
|-
| CAN channels
| 2
|-
| CAN Baud Rate
| 125K, 250K, 500K, 1M Baud
|-
| CAN Filters
| 14 per channel
|-
| CAN bus compatibility
| CAN 2.0 compatible, 1M baud
|-
| CAN termination
| Software controlled
|}

===Connections===
[[file:RaceCaptureApex_can_bus_pinout.png|700px]]

==Auxiliary Serial==
One Auxiliary RS232 compatible serial port is available on the main connector. You can use this to communicate with external devices that uses RS232 serial for communications.

[[image:RaceCaptureApex_aux_serial_pinout.png|700px]]

Control and communication of this Auxiliary serial port is provided through Lua Scripting, where you can control and receive data from external systems and map received data to virtual channels that can be provided in the telemetry stream.

* See the [[RaceCapturePro_Lua_Scripting|Lua scripting guide]] and [[RaceCapturePro_Lua_dScripting_Examples|Examples]]