Brentp at 04:44, 11 January 2019

2019-01-11T04:44:03Z

← Older revision		Revision as of 04:44, 11 January 2019
Line 1:		Line 1:
	You can print a custom enclosure for ShiftX3, or modify the design for your purposes.		You can print a custom enclosure for ShiftX3, or modify the design for your purposes.

			===3D CAD files===
			[[file:shiftx3_enclosure_rev_A.zip\|Download ShiftX3 enclosure Revision A]]

			The enclosure consists of the following parts:

			* shiftx3.stl : Main housing for ShiftX3 - Qty 1 needed
			* shiftx3_back_3dprint: Back cover for housing - Qty 1 needed
			* shiftx3_light_pipe.stl: Light pipe for LEDs - Qty 9 needed
			* shiftx3_light_pipe_photosensor.stl: Light pipe for photosensor - Qty 1 needed

	===Printing the enclosure===		===Printing the enclosure===

Brentp: Created page with "You can print a custom enclosure for ShiftX3, or modify the design for your purposes. ===Printing the enclosure=== Color and material are not critical for the enclosure; how..."

2019-01-11T04:42:38Z

Created page with "You can print a custom enclosure for ShiftX3, or modify the design for your purposes. ===Printing the enclosure=== Color and material are not critical for the enclosure; how..."

New page

You can print a custom enclosure for ShiftX3, or modify the design for your purposes.

===Printing the enclosure===
Color and material are not critical for the enclosure; however we recommend PETG or ABS.

===Printing light pipes===
Print the 9 LED light pipes and 1 photosensor light pipe in clear filament. PETG is recommended for optical clarity.

===Enclosure clean up===
Ensure extra filament is completely removed from the inside of the enclosure and is completely clean, so the ShiftX3 circuit board can fit flush and level inside the enclosure.

====3D printing notes====
* Print extra light pipes and print with a brim to purge heat-scorched / darkened filament from the extruder.
* Avoid printing just one light pipe at a time - printing just one will cause the part to sag and deform due to concentrated heat in the small part. We recommend you print at least 4 at a time to ensure heat is distributed across the parts and retain dimensional accuracy.

==Assembling the enclosure==
===Install light pipes===
Press the LED light pipes into the enclosure from the back side, ensuring they are flush with the front.

[[file:ShiftX3_white_enclosure_installing_light_pipes.jpg]]

* '''Note''' -The LED light pipes have a small lip that locks into the back surface.

Press the photo sensor light pipe into the front of the enclosure. There should be a tight interference fit; if there is not, use a tiny drop of super glue from the back side of the enclosure to secure it.

===Install ShiftX3===
Install ShiftX3 into the back of the enclosure, guiding the switches into their respective hole.

[[file:ShiftX3_white_enclosure_back.jpg]]

* '''Note''' - Take care to not torque the switch handles sideways to prevent damage.

Gently press the back of ShiftX3 board so that it is fully seated into the enclosure. There should be a 0.5mm lip around the back of the enclosure where the back plate will lock into place.

[[file:ShiftX3_white_enclosure_front.jpg]]

ShiftX3 in white ABS

[[file:ShiftX3_white_enclosure_light_pipes_installed_colors.jpg]]

[[file:ShiftX3_white_enclosure_light_pipes_installed_colors.jpg]]

[[file:ShiftX3_black_enclosure_light_pipes_installed_colors.jpg]]

ShiftX3 in black ABS

Install the back panel of ShiftX3 so the shallow lip of the back panel sits within the recess of the ShiftX3 enclosure.

When pressed together, there should be no gap between the enclosure and the back plate. If there is, check the inside of the enclosure to clean up any additional 3D printed filament.

Secure the back plate using two M2x5mm screws. Do not over-torque.

ShiftX3 3D printed enclosure - Revision history

Brentp at 04:44, 11 January 2019

Brentp: Created page with "You can print a custom enclosure for ShiftX3, or modify the design for your purposes. ===Printing the enclosure=== Color and material are not critical for the enclosure; how..."