CAN Crossover Cable: Difference between revisions

No edit summary
mNo edit summary
 
(19 intermediate revisions by the same user not shown)
Line 1: Line 1:
Most of Autosport Labs devices are wired to CAN Channel 1.  This can be a problem if you want to integrate 2 or more CAN systems that run at a different baud rate, or if they interfere with each other.  For example AIM CAN bus baud rate is 1M and OBDII baud rate is 500k.  Problem is the stock [https://www.autosportlabs.com/product/aim-dashboard-telemetry-cable/ ASL AIM to RCP cable] is wired to CAN 1 and the [https://www.autosportlabs.com/product/can-bus-obd-ii-cable ASL OBDII cable]  is also wired to CAN 1.  These two devices cannot be on the same CAN channel because they use different baud rates.  You can easily build an RJ45 CAN Crossover cable to swap the CAN 1 and CAN 2 channel wiring for that device.  You can either permanently modify one of the device's RJ45 cable, or create a CAN Crossover cable adapter.   
- Written by [https://www.facebook.com/scott.barton.76 Scott Barton] of [https://www.facebook.com/ProFormanceCoachingcom ProFormance Coaching]
 
Most of Autosport Labs CAN device cables are wired to CAN Bus Channel 1.  This can be a problem if you want to [https://wiki.autosportlabs.com/Multiple_CAN_Systems integrate 2 or more CAN systems] that run at a different baud rate, or if they interfere with each other.  For example AIM CAN bus baud rate is 1M and OBDII baud rate is 500k.  You can add both of these 2 CAN devices/systems to a Race Capture device with an [https://wiki.autosportlabs.com/Multiple_CAN_Systems#RJ45_Splitter RJ45 Splitter].  Problem is the stock [https://www.autosportlabs.com/product/aim-dashboard-telemetry-cable/ ASL AIM to RCP cable] is wired to CAN 1 and the [https://www.autosportlabs.com/product/can-bus-obd-ii-cable ASL OBDII cable]  is also wired to CAN 1.  These two devices cannot be on the same CAN channel because they use different baud rates.  You can easily build an RJ45 CAN Crossover cable to swap the CAN 1 and CAN 2 channel wiring for that CAN device/system.  You can either permanently modify one of the device's RJ45 cable, or create a CAN Crossover cable adapter.   


====You will need:====
====You will need:====
Line 19: Line 21:




====ASL Cables are wired the following:====
====ASL RJ45 CAN Cables are wired the following:====
*Pin1 (Orange/White): GND
*Pin1 (Orange/White): GND
*Pin2 (Orange): CAN1 High
*Pin2 (Orange): CAN1 High
*Pin3 (Green/White): CAN1Low
*Pin3 (Green/White): CAN1 Low
*Pin4 (Blue): CAN2 High
*Pin4 (Blue): CAN2 High
*Pin5  (Blue/White): CAN2 Low
*Pin5  (Blue/White): CAN2 Low
Line 31: Line 33:
   
   


So you can see that all we need to do is swap the wires for Pin 4 (Blue) and Pin 5 (Blue/White) with Pin2 (Orange) and Pin3 (Green/White) respectively on one of the RJ45 ends.
So you can see that all we need to do is swap the wires for Pin 4 (Blue) and Pin 5 (Blue/White) with Pin2 (Orange) and Pin3 (Green/White) respectively on one of the RJ45 ends.
 
====Our new CAN Crossover end will be wired:====
====Our new CAN Crossover end will be wired:====
*Pin1 (Orange/White): GND
*Pin1 (Orange/White): GND
Line 37: Line 40:
*Pin3 (Blue/White): CAN2 Low
*Pin3 (Blue/White): CAN2 Low
*Pin4 (Orange): CAN1 High
*Pin4 (Orange): CAN1 High
*Pin5  (Green/White): CAN1Low
*Pin5  (Green/White): CAN1 Low
*Pin6 (Green): N/C
*Pin6 (Green): N/C
*Pin7: (Brown/White): N/C  
*Pin7: (Brown/White): N/C  
Line 44: Line 47:




You can either cut off the RJ45 end on the stock ASL cable and modify it.  Or you can buy an [https://amzn.to/2WnYTj5 ethernet extension cable] and cut the male end off that and modify it to make an adapter that the stock ASL cable will plug into.   
You can cut off the RJ45 end on the stock ASL cable and modify it.  Or you can buy an [https://amzn.to/2WnYTj5 ethernet extension cable] and cut the female end off that and modify it to make a CAN Crossover adapter that the stock ASL cable will plug into as pictured below.   


[[Image:CANXOverAdapter.jpg|500px]]
[[Image:CANXOverAdapter.jpg|600px]]




Please see these directions for actually [https://www.warehousecables.com/landing/how-to-make-a-cat5-patch-cable.php cutting and crimping the RJ45 end] onto the CAT 5 cable.  You will just be using the crossover wiring order instead of the  T-568B wiring order.   
Please see these directions for actually [https://www.warehousecables.com/landing/how-to-make-a-cat5-patch-cable.php cutting and crimping the RJ45 end] onto the CAT 5 cable.  You will just be using the crossover wiring order mentioned above instead of the  T-568B wiring order.   


NOTE:  Only one of the RJ45 ends needs to be switched. to the CAN Crossover wiring.    Also when inserting the wires into the terminal, the locking mechanism should be facing down.  You should be looking at the metal pins.
NOTE:  Only one of the RJ45 ends needs to be switched to the CAN Crossover wiring.    Also when inserting the wires into the terminal, the locking mechanism should be facing down.  You should be looking at the metal pins.


More info on ASL CAN cables.  https://wiki.autosportlabs.com/RacecapturePro_MK3_hardware_install#RJ45_CAN_.2B_Power_connection
More info on ASL CAN cables.  https://wiki.autosportlabs.com/RacecapturePro_MK3_hardware_install#RJ45_CAN_.2B_Power_connection

Latest revision as of 19:51, 5 January 2021

- Written by Scott Barton of ProFormance Coaching

Most of Autosport Labs CAN device cables are wired to CAN Bus Channel 1. This can be a problem if you want to integrate 2 or more CAN systems that run at a different baud rate, or if they interfere with each other. For example AIM CAN bus baud rate is 1M and OBDII baud rate is 500k. You can add both of these 2 CAN devices/systems to a Race Capture device with an RJ45 Splitter. Problem is the stock ASL AIM to RCP cable is wired to CAN 1 and the ASL OBDII cable is also wired to CAN 1. These two devices cannot be on the same CAN channel because they use different baud rates. You can easily build an RJ45 CAN Crossover cable to swap the CAN 1 and CAN 2 channel wiring for that CAN device/system. You can either permanently modify one of the device's RJ45 cable, or create a CAN Crossover cable adapter.

You will need:


Most ethernet cables (including the ASL cables) are wired in T-568B which is

  • Pin1: Orange/White
  • Pin2: Orange
  • Pin3: Green/White
  • Pin4: Blue
  • Pin5: Blue/White
  • Pin6: Green
  • Pin7: Brown/White
  • Pin8: Brown

T568B.gif


ASL RJ45 CAN Cables are wired the following:

  • Pin1 (Orange/White): GND
  • Pin2 (Orange): CAN1 High
  • Pin3 (Green/White): CAN1 Low
  • Pin4 (Blue): CAN2 High
  • Pin5 (Blue/White): CAN2 Low
  • Pin6 (Green): N/C
  • Pin7: (Brown/White): N/C
  • Pin8: (Brown): 12v

RaceCapturePro MK3 RJ45 pinout.png


So you can see that all we need to do is swap the wires for Pin 4 (Blue) and Pin 5 (Blue/White) with Pin2 (Orange) and Pin3 (Green/White) respectively on one of the RJ45 ends.

Our new CAN Crossover end will be wired:

  • Pin1 (Orange/White): GND
  • Pin2 (Blue): CAN2 High
  • Pin3 (Blue/White): CAN2 Low
  • Pin4 (Orange): CAN1 High
  • Pin5 (Green/White): CAN1 Low
  • Pin6 (Green): N/C
  • Pin7: (Brown/White): N/C
  • Pin8: (Brown): 12v

CANCrossOver.jpg


You can cut off the RJ45 end on the stock ASL cable and modify it. Or you can buy an ethernet extension cable and cut the female end off that and modify it to make a CAN Crossover adapter that the stock ASL cable will plug into as pictured below.

CANXOverAdapter.jpg


Please see these directions for actually cutting and crimping the RJ45 end onto the CAT 5 cable. You will just be using the crossover wiring order mentioned above instead of the T-568B wiring order.

NOTE: Only one of the RJ45 ends needs to be switched to the CAN Crossover wiring. Also when inserting the wires into the terminal, the locking mechanism should be facing down. You should be looking at the metal pins.

More info on ASL CAN cables. https://wiki.autosportlabs.com/RacecapturePro_MK3_hardware_install#RJ45_CAN_.2B_Power_connection


NOTE: If you wire a device to CAN bus 2, you will probably have to go into each channel and change it from CAN Bus 1 to CAN Bus 2.

RC CANBus.jpg