RaceCapturePro Lua Scripting: Difference between revisions

(37 intermediate revisions by 3 users not shown)
Line 1: Line 1:
=RaceCapture/Pro Scripting Guide=
==Example Scripts and How-Tos==
==Example Scripts and How-Tos==
A large collection of example scripts can be found in our '''[[RaceCapturePro Lua Scripting Examples|Lua Scripting Examples]]'''


'''[[RaceCapturePro Lua Scripting Examples|Lua Scripting Examples]]'''
==Lua Script Basics==
 
===Conventions===
* All inputs and outputs are numbered starting at 0 (getGpio(0), setChannel(0), etc)
* All channel values must be numbers
* All virtual channel names must have no spaces (to be fixed in future revisions)
 
====Writing your script====
 
=====onTick() function=====
Your Lua script is centered around the onTick() function. RaceCapture/Pro will periodically call this function, and here you can define your custom tasks and logic.
 
Example: this script will periodically write a message to the log:
<pre>
function onTick()
  println("hello from RaceCapture/Pro")
end
</pre>
 
=====Viewing the output log=====
You can observe the loading of new script and monitor and debug the behavior of your script by using the print() / println() functions. In order to see the log output, enable the "Poll Log" checkbox in the scripting window:
 
[[image:Hello_RaceCapturePro_script.png|800px]]
 
=====Controlling the onTick() rate=====
You can control how fast your script is executed using the setTickRate() function.  The tick Rate is specified in Hz, and the default rate is 1Hz.
 
<pre>
count = 0
setTickRate(10)
 
function onTick()
  count = count + 1
  println("Tick: " ..count)
end
</pre>
 
[[image:RaceCapture_tick_count.png|800px]]
 
=====Reading and controlling inputs and outputs=====
 
The Lua scripting enables endless combinations of custom behaviors by reading sensor values, controlling output lines, broadcasting CAN messages and writing data to the Auxiliary serial port.
 
Example: Reading a sensor value and activating an output based on a threshold.
 
Given:
* A calibrated temperature sensor is connected to the first analog input (0);
* The first GPIO is configured for output mode
 
This script will activate the output upon crossing the temperature threshold of 212.
 
<pre>
function onTick()
  temperature = getAnalog(0)
  if temperature > 212 then
    setGpio(0, 1)
  else
    setGpio(0, 0)
  end
end
</pre>
=====Combining multiple functions=====
When combining multiple functions into one script, it's recommended to break them into multiple functions and reference them from the main onTick() function.
 
Example:
 
<pre>
function checkTemps()
 
[ temperature checking logic goes here ]
 
end
 
function checkAutoLogging()
 
[ automatic logging logic goes here ]
 
end
 
function onTick()
  checkTemps()
  checkAutoLogging()
end
</pre>
 
=====Debugging your script=====
If you're not sure why your script is misbehaving, you can use the println() function to output messages in the log and observe how your script is behaving.
 
Example:
 
<pre>
function onTick()
  temperature = getAnalog(0)
  println("current temp: " ..temperature)
  if temperature > 212 then
    println("over temp!")
    setGpio(0, 1)
  else
    println("under temp")
    setGpio(0, 0)
  end
end
</pre>
 
=====Lua Reference=====
RaceCapture/Pro uses the standard, lightweight Lua scripting language used as an extension / customization language for many software applications and especially gaming.
 
* See [https://www.lua.org/ lua.org] for additional information on how to use the Lua language
=====More examples=====
You can see more examples in our [[RaceCapturePro Lua Scripting Examples|Lua Scripting Examples]] section.
 
=API Reference=


==General Input / Output (GPIO) Functions==
==General Input / Output (GPIO) Functions==
Line 21: Line 134:


*params
*params
** channel: integer 0 - 2, state - 1 = output active; 0 = output inactive
** channel: integer 0 - 2
** state: (int / ''(since 2.10.0)'' bool) 1 / true = output active; 0 / false = output inactive
*returns:
*returns:
** none
** none
Line 38: Line 152:


==PWM / Analog Output functions==
==PWM / Analog Output functions==
'''PWM / Analog outputs only apply to RaceCapture/Pro MK1 and MK2''


===setPwmDutyCycle( channel, dutyCyclePct )===
===setPwmDutyCycle( channel, dutyCyclePct )===
Line 71: Line 186:


*params
*params
** channel: Timer channel 0 - 2
** channel: Timer channel. Zero based, so first channel is 0, 2nd channel is 1, and so on.
** returns: RPM value
** returns: RPM value


Line 78: Line 193:


*params
*params
** channel: Timer channel 0 - 3
** channel: Timer channel 0 - 3. Zero based, so first channel is 0, 2nd channel is 1, and so on.
** returns:  millisecond value
** returns:  millisecond value


Line 85: Line 200:


*params
*params
** channel: Timer channel 0 - 3
** channel: Timer channel. Zero based, so first channel is 0, 2nd channel is 1, and so on.
** returns:  Frequency in Hz
** returns:  Frequency in Hz


Line 92: Line 207:


*params
*params
** channel: Timer channel 0 - 3
** channel: Timer channel 0 - 3. Zero based, so first channel is 0, 2nd channel is 1, and so on.
** returns: Raw timer value between 0 - 65535
** returns: Raw timer value between 0 - 65535


Line 103: Line 218:
      
      
===getAnalog(channel)===
===getAnalog(channel)===
Reads the scaled analog value for the specified analog input channel.
Reads the scaled analog value for the specified analog input channel.  
 
*params
*params
** channel: Analog input channel 0 - 7
** channel: Analog input channel.  Zero based, so first channel is 0, 2nd channel is 1, and so on.
*** Note: channel 7 is internally dedicated to battery voltage.
*** Note: the last Analog input is connected to battery voltage:
**** Channel 7 on RaceCapture/Pro MK1 and MK2
****Channel 8 on RaceCapture/Pro MK3 and RaceCapture Apex
** returns: Scaled / calculated value for the specified analog channel as defined in the channel scaling configuration
** returns: Scaled / calculated value for the specified analog channel as defined in the channel scaling configuration


Line 114: Line 232:
Reads the specified IMU channel
Reads the specified IMU channel
* params
* params
** channel (0 - 2 for accelerometer, 3 for yaw gyro sensor)
** channel (0 = X, 1 = Y,  2=Z, 3= Yaw, 4= Pitch, 5 = Roll)
* returns
* returns
** The value scaled to G force, or degrees/sec depending on the channel selected
** The value scaled to G force, or degrees/sec depending on the channel selected
Line 121: Line 239:
Reads the raw value of the specified accelerometer or yaw channel
Reads the raw value of the specified accelerometer or yaw channel
* params
* params
** channel (0 - 2 for accelerometer, 3 for yaw gyro sensor)
** channel (0 = X, 1 = Y,  2=Z, 3= Yaw, 4= Pitch, 5 = Roll)
* returns
* returns
** The raw accelerometer value
** The raw accelerometer value
Line 149: Line 267:
** The current GPS quality indicator
** The current GPS quality indicator
** 0: No fix; 1: Fixed; 2: SPS Fix; 3: Differential Fix
** 0: No fix; 1: Fixed; 2: SPS Fix; 3: Differential Fix
===getGpsSats()===
* params
** (none)
* returns
** The number of GPS satellites currently used in the fix


===getGpsTime()===
===getGpsTime()===
Line 183: Line 307:
* returns
* returns
** The last measured lap time in decimal minutes / seconds
** The last measured lap time in decimal minutes / seconds
===getPredTime()===
''as of 2.12.0 firmware''
Provides the current Predicted Lap time time as determined by the start/finish line configuration and measured by the attached GPS module. A training lap is required before the predicted time is valid.
* params
** (none)
* returns
** The current predicted time in decimal minutes / seconds


===getGpsSec()===
===getGpsSec()===
Line 221: Line 354:
** channel: The CAN channel. 0 for the first channel, 1 for the 2nd, if supported on the hardware
** channel: The CAN channel. 0 for the first channel, 1 for the 2nd, if supported on the hardware
** baud rate: Supported baud rates: 100000, 125000, 250000, 500000, 1000000
** baud rate: Supported baud rates: 100000, 125000, 250000, 500000, 1000000
** termination: 1 to enable termination, 0 to disable. Defaults to 1 (enabled) ''Only available on RaceCapture/Pro MK3 and RaceCapture/Apex. On other platforms this setting has no effect''.
* returns
* returns
** 1 if successful, 0 if initialization fails, nil if parameters are incorrect
** 1 if successful, 0 if initialization fails, nil if parameters are incorrect
Line 249: Line 383:
* params
* params
** channel: The CAN channel. 0 for the first channel, 1 for the 2nd, if supported on the hardware
** channel: The CAN channel. 0 for the first channel, 1 for the 2nd, if supported on the hardware
** timeout (optional). read timeout in milliseconds. defaults to 100ms
** timeout (optional). read timeout in milliseconds. defaults to 100ms.  For non-blocking functionality specify a timeout of 0.
* returns
* returns
** identifier: The Identifier value of the message, either in standard (11 bit) or extended (29 bit) format.
** identifier: The Identifier value of the message, either in standard (11 bit) or extended (29 bit) format.
Line 265: Line 399:
===setCANfilter(channel, filterId, extended, filter, mask )===
===setCANfilter(channel, filterId, extended, filter, mask )===
''available in firmware 2.0''
''available in firmware 2.0''
Sets the specified CAN filter ID, to ignore messages with a particular address. Must use in combination with setCANMask() to set a complete filter and mask.
Sets the specified CAN filter and mask ID, to ignore CAN messages that match a particular ID pattern.  
* params
* params
** channel: The CAN channel. 0 for the first channel, 1 for the 2nd, if supported on the hardware
** channel: The CAN channel. 0 for the first channel, 1 for the 2nd, if supported on the hardware
Line 307: Line 441:
* returns
* returns
** (none)
** (none)
==SD Logging control==
The following functions control logging operations to the internal SD card.
* '''Note:''' Only SD card logging is controlled; External devices or apps connected to the telemetry stream are not affected by these commands.
===isLogging()===
Indicates if an SD card logging session is in progress
* params
** (none)
* returns
** 0 if not logging, non zero otherwise.


===startLogging()===
===startLogging()===
Begins a logging session
Begins a logging session to the SD card.  If currently logging, this function has no effect.
* '''Note:''' If an error occurs during writing, the error indicator on the front panel, if provided, will illuminate.
* params
* params
** (none)
** (none)
Line 316: Line 461:


===stopLogging()===
===stopLogging()===
Stops the current logging session. If not logging, this function has no effect.
Stops the current SD card logging session. If not logging, this function has no effect.
* params
* params
** (none)
** (none)
Line 326: Line 471:
* params
* params
** led (1-3)
** led (1-3)
** state : 1 = on, 0 = off
** state: (int / ''[as of 2.10.0]'' bool) 1 / true = on, 0 / false = off
* returns
** (none)
 
===setBgStream( on/off )===
Sets the state of background streaming
* params
** Boolean: true for on, false for off.
* returns
* returns
** (none)
** (none)
===getBgStream()===
Gets the state of background streaming
* params
** (none)
* returns
** Boolean: True for on, false for off.


==Serial Port Communications==
==Serial Port Communications==
Line 337: Line 496:
0 = USB port<br/>
0 = USB port<br/>
1 = GPS port<br/>
1 = GPS port<br/>
2 = Internal telemetry port (MK2 only)<br/>
2 = Internal telemetry port (MK2/3/Apex only)<br/>
3 = Wireless / Bluetooth port<br/>
3 = Bluetooth port<br/>
4 = Auxiliary port<br/>
4 = Auxiliary / WiFi port<br/>
5 = WiFi port
6 = External Auxiliary port (RaceCapture/Pro MK3 and RaceCapture/Apex only)


* '''Note''': We only recommend using ports 3 and 4 for connecting script to external devices. Ports 0 - 2 have been included for reference; using them may interfere with normal operations of the unit.
* '''Note''': We only recommend using ports 3 and 4 for connecting script to external devices. Ports 0 - 2 have been included for reference; using them may interfere with normal operations of the unit.
Line 427: Line 588:
===addChannel( name, sampleRate, [precision], [min], [max], [units] )===
===addChannel( name, sampleRate, [precision], [min], [max], [units] )===
''available in firmware 2.0''
''available in firmware 2.0''
Adds a virtual channel. This virtual channel remains in memory during runtime; it is not persisted in the configuration. Up to 30 virtual channels can be created.
Adds a virtual channel. This virtual channel remains in memory during runtime; it is not persisted in the configuration. Up to 100 virtual channels can be created.
* params
* params
** name: The name of the channel, up to 10 characters long. We recommend using an existing System channel name as defined by the app when possible.
** name: The name of the channel, up to 10 characters long. We recommend using an existing System channel name as defined by the app when possible.
Line 438: Line 599:
* returns
* returns
** the id of the new virtual channel, or NIL if the virtual channel could not be created. Use this id for setting the channel value (see setChannel() )
** the id of the new virtual channel, or NIL if the virtual channel could not be created. Use this id for setting the channel value (see setChannel() )
===getChannel( <Channel ID | Channel Name> )===
* Available: v2.9.0
* Parameters
** Channel ID (number) - The channel id value as provided by the ''addChannel'' method.
** Channel Name (string) - The name of the channel as provided to the ''addChannel'' method.  Using the Channel ID method is preferred and is faster.
* Returns
** (number) The value of the channel.
* Examples:
** <code> val = getChannel(1) </code>
** <code> val = getChannel("foo") </code>


===setChannel( channelId, value )===
===setChannel( channelId, value )===
Line 468: Line 640:
===getDateTime()===
===getDateTime()===
''Available since firmware 2.8.4''<br>
''Available since firmware 2.8.4''<br>
Returns date and time info to the best of the systems ability.  Only available after GPS lock has been established.  Will return epoch time (Jan 1, 1970 00:00:000) if time is not available.
Returns date and time info to the best of the systems ability, in UTC.  Only available after GPS lock has been established.  Will return epoch time (Jan 1, 1970 00:00:000) if time is not available.


* Returns: A list of date and time information in the following order:
* Returns: A list of date and time information in the following order:
Line 475: Line 647:
** Day
** Day
** Hour
** Hour
** Minute
** Second
** Second
** Millisecond
** Millisecond

Revision as of 20:53, 15 September 2017

RaceCapture/Pro Scripting Guide

Example Scripts and How-Tos

A large collection of example scripts can be found in our Lua Scripting Examples

Lua Script Basics

Conventions

  • All inputs and outputs are numbered starting at 0 (getGpio(0), setChannel(0), etc)
  • All channel values must be numbers
  • All virtual channel names must have no spaces (to be fixed in future revisions)

Writing your script

onTick() function

Your Lua script is centered around the onTick() function. RaceCapture/Pro will periodically call this function, and here you can define your custom tasks and logic.

Example: this script will periodically write a message to the log:

function onTick()
  println("hello from RaceCapture/Pro")
end
Viewing the output log

You can observe the loading of new script and monitor and debug the behavior of your script by using the print() / println() functions. In order to see the log output, enable the "Poll Log" checkbox in the scripting window:

Hello RaceCapturePro script.png

Controlling the onTick() rate

You can control how fast your script is executed using the setTickRate() function. The tick Rate is specified in Hz, and the default rate is 1Hz.

count = 0
setTickRate(10)

function onTick()
  count = count + 1
  println("Tick: " ..count)
end

RaceCapture tick count.png

Reading and controlling inputs and outputs

The Lua scripting enables endless combinations of custom behaviors by reading sensor values, controlling output lines, broadcasting CAN messages and writing data to the Auxiliary serial port.

Example: Reading a sensor value and activating an output based on a threshold.

Given:

  • A calibrated temperature sensor is connected to the first analog input (0);
  • The first GPIO is configured for output mode

This script will activate the output upon crossing the temperature threshold of 212.

function onTick()
  temperature = getAnalog(0)
  if temperature > 212 then
    setGpio(0, 1)
  else
    setGpio(0, 0)
  end
end
Combining multiple functions

When combining multiple functions into one script, it's recommended to break them into multiple functions and reference them from the main onTick() function.

Example:

function checkTemps()

[ temperature checking logic goes here ]

end

function checkAutoLogging()

[ automatic logging logic goes here ]

end

function onTick()
  checkTemps()
  checkAutoLogging()
end
Debugging your script

If you're not sure why your script is misbehaving, you can use the println() function to output messages in the log and observe how your script is behaving.

Example:

function onTick()
  temperature = getAnalog(0)
  println("current temp: " ..temperature)
  if temperature > 212 then
    println("over temp!")
    setGpio(0, 1)
  else
    println("under temp")
    setGpio(0, 0)
  end
end
Lua Reference

RaceCapture/Pro uses the standard, lightweight Lua scripting language used as an extension / customization language for many software applications and especially gaming.

  • See lua.org for additional information on how to use the Lua language
More examples

You can see more examples in our Lua Scripting Examples section.

API Reference

General Input / Output (GPIO) Functions

getGpio( channel )

Retrieves the state of the specified GPIO channel

  • params
    • channel: integer 0 - 2
  • returns:
    • state: 1 = channel is high, 0 = channel is low

When the channel is configured for input mode, a voltage high input (> 2 volts) will read as 1; a voltage low will read as 0. A disconnected channel will read as high due to the internal pullup resistor.

When the channel is configured as output, the channel reads 1 when the channel is activated (output transistor is connected to ground) and 0 when the channel is deactivated (pullup resistor is active)

setGpio ( channel, state )

Sets the state of the GPIO channel when the channel is configured for output mode.

  • params
    • channel: integer 0 - 2
    • state: (int / (since 2.10.0) bool) 1 / true = output active; 0 / false = output inactive
  • returns:
    • none

When the state specified is 1, the output is active (transistor is connected to ground). When state is 0, transistor is disconnected, and pullup resistor is active.

When configured for input mode this function has no effect.

getButton()

Gets the state of the front panel pushbutton.

  • params
    • none
  • returns
    • state: 1 = pushbutton is depressed; 0 = pushbutton is not depressed

PWM / Analog Output functions

'PWM / Analog outputs only apply to RaceCapture/Pro MK1 and MK2

setPwmDutyCycle( channel, dutyCyclePct )

Sets the duty cycle of the specified PWM / Analog output channel to the specified duty cycle percentage

  • params
    • channel: PWM / Analog output channel 0 - 3
    • dutyCyclePct: Percentage value of the duty cycle as a counting number 0 - 100
  • returns
    • none

setPwmClockFreq( frequency )

Sets the clock frequency of the PWM outputs

  • params
    • frequency: the frequency of the PWM clock, in Hz. Supported range is 320-40000 Hz
  • returns
    • none

setAnalogOut( channel, voltage )

Sets the output voltage of the specified PWM / Analog output channel to the specified period. A convenience function equivalent to setPwmDutyCycle that translates voltage to PWM percentage.

  • params
    • channel: PWM / Analog output channel 0 - 3
    • voltage: the specified output voltage ( 0 - 5v)
    • returns
  • none

Timer / RPM Sensor Functions

getTimerRpm(channel)

Returns the current RPM of the specified timer input channel. Note, the timer channel configuration must be set to RPM mode.

  • params
    • channel: Timer channel. Zero based, so first channel is 0, 2nd channel is 1, and so on.
    • returns: RPM value

getTimerPeriodMs(channel)

Returns the current duration of the full cycle pulse of the specified timer input channel, in milliseconds. Note the timer channel configuration must be set to Duration mode.

  • params
    • channel: Timer channel 0 - 3. Zero based, so first channel is 0, 2nd channel is 1, and so on.
    • returns: millisecond value

getTimerFreq(channel)

Returns the current frequency present on the specified timer input channel, in Hz. Note the timer channel configuration must be set to Frequency Mode.

  • params
    • channel: Timer channel. Zero based, so first channel is 0, 2nd channel is 1, and so on.
    • returns: Frequency in Hz

getTimerRaw(channel)

Returns the current raw timer value as measured on the specified timer input channel.

  • params
    • channel: Timer channel 0 - 3. Zero based, so first channel is 0, 2nd channel is 1, and so on.
    • returns: Raw timer value between 0 - 65535


Analog Sensor Functions

getAnalog(channel)

Reads the scaled analog value for the specified analog input channel.

  • params
    • channel: Analog input channel. Zero based, so first channel is 0, 2nd channel is 1, and so on.
      • Note: the last Analog input is connected to battery voltage:
        • Channel 7 on RaceCapture/Pro MK1 and MK2
        • Channel 8 on RaceCapture/Pro MK3 and RaceCapture Apex
    • returns: Scaled / calculated value for the specified analog channel as defined in the channel scaling configuration

Accelerometer / Yaw Sensor Functions

getImu(channel)

Reads the specified IMU channel

  • params
    • channel (0 = X, 1 = Y, 2=Z, 3= Yaw, 4= Pitch, 5 = Roll)
  • returns
    • The value scaled to G force, or degrees/sec depending on the channel selected

getImuRaw(channel)

Reads the raw value of the specified accelerometer or yaw channel

  • params
    • channel (0 = X, 1 = Y, 2=Z, 3= Yaw, 4= Pitch, 5 = Roll)
  • returns
    • The raw accelerometer value

GPS Sensor Functions

getGpsPos()

Reads the current position as measured by the attached GPS module coming in firmware 2.0

  • params
    • none
  • returns
    • Latitude: latitude in decimal degrees
    • Longitude: longitude in decimal degress

getGpsSpeed()

Provides the current speed as measured by the attached GPS module

  • params
    • (none)
  • returns
    • The current speed in MPH

getGpsQuality()

Provides the current GPS quality indicator as indicated by the attached GPS module

  • params
    • (none)
  • returns
    • The current GPS quality indicator
    • 0: No fix; 1: Fixed; 2: SPS Fix; 3: Differential Fix

getGpsSats()

  • params
    • (none)
  • returns
    • The number of GPS satellites currently used in the fix

getGpsTime()

Provides the current GPS time as indicated by the attached GPS module (in NMEA format) todo: document this

  • params
    • (none)
  • returns
    • The current GPS time value

getGpsDist()

Provides the current GPS calculated distance from the beginning of the logging session, or from the start finish line, if configured.

  • params
    • (none)
  • returns
    • The distance, in Miles

getGpsAltitude()

Provides the current GPS calculated altitude from sea level in feet. The method will return 0 if there is no GPS lock.

  • Added: v2.9.0
  • Parameters: None
  • Returns: <altitude>

getLapCount()

Provides the current Lap Count as determined by the start/finish line configuration and measured by the attached GPS module.

  • params
    • (none)
  • returns
    • The number of laps detected since the logging session started

getLapTime()

Provides the last lap time as determined by the start/finish line configuration and measured by the attached GPS module.

  • params
    • (none)
  • returns
    • The last measured lap time in decimal minutes / seconds

getPredTime()

as of 2.12.0 firmware

Provides the current Predicted Lap time time as determined by the start/finish line configuration and measured by the attached GPS module. A training lap is required before the predicted time is valid.

  • params
    • (none)
  • returns
    • The current predicted time in decimal minutes / seconds

getGpsSec()

Provides the number of seconds since midnight, as measured by the GPS module. todo: how does this relate to timezone? GMT or local?

  • params
    • (none)
  • returns
    • number of seconds since midnight, as measured by the attached GPS module

getAtStartFinish()

Indicates if within the start finish line target as determined by the start/finish line configuration and measured by the attached GPS module.

  • params
    • (none)
  • returns
    • 1 if currently within the start/finish line target, 0 if outside

getTimeDiff(time1, time2)

Utility function to calculate the absolute difference between two time values, in seconds. todo: investigate the need for this function. may be eliminated in 1.2 firmware

  • params
    • time1
    • time2
  • returns
    • The absolute difference between the specified values

getTimeSince(time)

Utility function to calculate the time since midnight, in seconds. todo: investigate the need for this function. may be eliminated in 1.2 firmware

  • params
    • time
  • returns
    • The number of seconds since midnight

CAN Bus functions

initCAN(channel, baud )

available in firmware 2.0 Initializes the CAN bus module. Normally this is done when RaceCapture/Pro powers on; use this function if you need to change the CAN baud rate on the fly.

  • params
    • channel: The CAN channel. 0 for the first channel, 1 for the 2nd, if supported on the hardware
    • baud rate: Supported baud rates: 100000, 125000, 250000, 500000, 1000000
    • termination: 1 to enable termination, 0 to disable. Defaults to 1 (enabled) Only available on RaceCapture/Pro MK3 and RaceCapture/Apex. On other platforms this setting has no effect.
  • returns
    • 1 if successful, 0 if initialization fails, nil if parameters are incorrect

txCAN(channel, id, isExtended, data, [timeout] )

available in firmware 2.0 Transmit a CAN message.

  • params
    • channel: The CAN channel. 0 for the first channel, 1 for the 2nd, if supported on the hardware
    • identifier: The Identifier value of the message, either in standard (11 bit) or extended (29 bit) format.
    • isExtended: 0 for Standard (11 bit) Identifier or 1 for Extended (29 bit) Identifier.
    • data: CAN message payload; array up to 8 elements long.
    • timeout: (optional) specify a timeout for sending this message. if the transmit queue is full, will block for the specified milliseconds. Defaults to 100ms
  • returns
    • 1 if successful, 0 if failed, nil if parameters are incorrect


Example:

channel = 0
id = 1234
ext = 0
data = {11,22,33}
res = txCAN(channel, id, ext, data)

rxCAN(channel, [timeout] )

available in firmware 2.0 Receive a CAN message, if available.

  • params
    • channel: The CAN channel. 0 for the first channel, 1 for the 2nd, if supported on the hardware
    • timeout (optional). read timeout in milliseconds. defaults to 100ms. For non-blocking functionality specify a timeout of 0.
  • returns
    • identifier: The Identifier value of the message, either in standard (11 bit) or extended (29 bit) format.
    • isExtended: 0 for Standard (11 bit) Identifier or 1 for Extended (29 bit) Identifier.
    • Data: CAN message payload; array up to 8 elements long.

If no CAN message was received, the function returns nil

Example:

id, ext, data = rxCAN(0, 100) --100ms timeout
if id ~= nil then
  println("CAN rx: " ..id .." " ..data[1]) --print ID and first element of received message
end

setCANfilter(channel, filterId, extended, filter, mask )

available in firmware 2.0 Sets the specified CAN filter and mask ID, to ignore CAN messages that match a particular ID pattern.

  • params
    • channel: The CAN channel. 0 for the first channel, 1 for the 2nd, if supported on the hardware
    • filterId: The id of the filter. Up to 6 filters are supported on MK1, 15 per channel on MK2. Filter ids start at 0.
    • extended: 0 for Standard (11 bit) Identifier or 1 for Extended (29 bit) Identifier.
    • filter: Pattern value for CAN filter
    • mask: the mask for the CAN filter
  • returns
    • 1 for success, 0 for fail, nil if parameters are incorrect

readOBD2( PID )

available in firmware 2.0 Reads an OBD2 PID and returns the calculated value. This is a convenience method wrapped around the built-in CAN functions.

  • params
    • The OBD2 PID to read. Supported PIDs (TBD documented)
  • returns
    • The calculated PID value, or nil if the OBD2 PID was invalid or could not be read (e.g. CAN receive message timeout)

Logger Control Functions

onTick()

  • params:
    • (none)
  • returns:
    • (none)

The onTick() function is the main loop where scripting activity takes place. By default it is called by RaceCapture/Pro every 1 second (1Hz). The rate can be adjusted using the setTickRate() function.

  • Note - you should only define one onTick() function in your code. If multiple onTick() functions are defined, only the last defined onTick() function will be used.

Example:

function onTick()
  println("Hello") --write something to the log
end

setTickRate(rate)

Sets the rate at which the onTick() function is called

  • params
    • rate: The rate the onTick() function is called, in Hz. Max tick rate is 30Hz.
  • returns
    • (none)

SD Logging control

The following functions control logging operations to the internal SD card.

  • Note: Only SD card logging is controlled; External devices or apps connected to the telemetry stream are not affected by these commands.

isLogging()

Indicates if an SD card logging session is in progress

  • params
    • (none)
  • returns
    • 0 if not logging, non zero otherwise.

startLogging()

Begins a logging session to the SD card. If currently logging, this function has no effect.

  • Note: If an error occurs during writing, the error indicator on the front panel, if provided, will illuminate.
  • params
    • (none)
  • returns
    • (none)

stopLogging()

Stops the current SD card logging session. If not logging, this function has no effect.

  • params
    • (none)
  • returns
    • (none)

setLed( led, state )

Sets the state of a front panel LED

  • params
    • led (1-3)
    • state: (int / [as of 2.10.0] bool) 1 / true = on, 0 / false = off
  • returns
    • (none)

setBgStream( on/off )

Sets the state of background streaming

  • params
    • Boolean: true for on, false for off.
  • returns
    • (none)

getBgStream()

Gets the state of background streaming

  • params
    • (none)
  • returns
    • Boolean: True for on, false for off.

Serial Port Communications

These function calls allow reading / writing line oriented data from the built in serial ports.

Port mappings

0 = USB port
1 = GPS port
2 = Internal telemetry port (MK2/3/Apex only)
3 = Bluetooth port
4 = Auxiliary / WiFi port
5 = WiFi port 6 = External Auxiliary port (RaceCapture/Pro MK3 and RaceCapture/Apex only)

  • Note: We only recommend using ports 3 and 4 for connecting script to external devices. Ports 0 - 2 have been included for reference; using them may interfere with normal operations of the unit.

initSer( port, baud, bits, parity, stopBits)

Initializes the specified serial port

  • params
    • port: The port to initialize. (defaults to Auxiliary port)
    • baud: The baud rate to set (defaults to 115200)
    • bits: Number of bit in the message (8 or 7) (defaults to 8)
    • parity: (1 = Even Parity, 2 = Odd Parity, 0 = No Parity) (defaults to No Parity)
    • stopBits: number of stop bits (1 or 2) (defaults to 1)
  • returns
    • 1 if initialization succeeds, -1 if parameters are incorrect

readCSer( port, [timeout])

Available since firmware 2.8.4
Read a character from the specified serial port

  • params
    • port: The port to read. (required)
    • timeout - the read timeout, in ms.
  • returns
    • the character read, or nil if the timeout was reached

readSer( port, [timeout])

Read a line of data from the specified serial port. This command blocks until a newline ('\n') character is received on the port, or a timeout occurs.

  • params
    • port: Serial port 0 - 4
    • timeout - the read timeout, in ms.
    • returns: a line of serial data, or nil if the timeout was reached

writeCSer( port, data )

Available since firmware 2.8.4
Writes the specified character to the serial port. The call will block until the character is written.

  • params:
    • port - the serial port to write
    • char - the character to write.
  • returns:

(no return values)

writeSer( port, data )

Writes a line of data to the specified serial port, appending a newline at the end. The call will block until all characters are written.

  • params
    • port: Serial port 0 - 4
    • data: the data in string format
  • returns:

(no return values)

Logger Configuration Functions

flashLoggerCfg()

Writes the current configuration in RAM to flash memory.

  • params
    • (none)
  • returns
    • (none)

setPwmClockFreq( freq )

Sets the clock frequency for all PWM channels

  • params
    • freq: The clock frequency todo: what units?
  • returns
    • (none)

getPwmClockFreq()

Gets the PWM clock frequency controlling all PWM channels

  • params
    • (none)
  • returns
    • the PWM clock frequency todo: what units?

calibrateImuZero()

Automatically Calibrates the accelerometer zero position.

  • params
    • (none)
  • returns
    • (none)

Virtual Channels

addChannel( name, sampleRate, [precision], [min], [max], [units] )

available in firmware 2.0 Adds a virtual channel. This virtual channel remains in memory during runtime; it is not persisted in the configuration. Up to 100 virtual channels can be created.

  • params
    • name: The name of the channel, up to 10 characters long. We recommend using an existing System channel name as defined by the app when possible.
    • sampleRate: A supported sample rate (1,10,25,50,100,200Hz)
    • precision: (optional) the numerical precision (number of decimal places) used when logging to SD and telemetry. Defaults to 2
    • min: (optional) The min expected value for this channel. Defaults to 0
    • max: (optional) The max expected value for this channel. Defaults to 1000
    • units: (optional) The units label for this channel. Defaults to empty string / none
  • returns
    • the id of the new virtual channel, or NIL if the virtual channel could not be created. Use this id for setting the channel value (see setChannel() )

getChannel( <Channel ID | Channel Name> )

  • Available: v2.9.0
  • Parameters
    • Channel ID (number) - The channel id value as provided by the addChannel method.
    • Channel Name (string) - The name of the channel as provided to the addChannel method. Using the Channel ID method is preferred and is faster.
  • Returns
    • (number) The value of the channel.
  • Examples:
    • val = getChannel(1)
    • val = getChannel("foo")

setChannel( channelId, value )

available in firmware 2.0 Updates the value of a previously created virtual channel.

  • params
    • channelId: the ID of the channel provided by addChannel()
    • value: the new value to set for the virtual channel

Example:

id = addChannel("EGT", 1)

function onTick()
   temp = getAnalog(0) --read analog channel 0
   temp = temp * 1000
   setChannel(id, temp) --sets the virtual channel value
end

Time Info

These methods get you information about dates and time. This is useful in controlling script behavior or just knowing what time it is.

getUptime()

Available since firmware 2.8.4
Returns the number of miliseconds since the device last started. This is always available and is the most consistent way to time things in LUA script on RaceCapture.

  • Returns
    • Number of milliseconds since CPU boot.

getDateTime()

Available since firmware 2.8.4
Returns date and time info to the best of the systems ability, in UTC. Only available after GPS lock has been established. Will return epoch time (Jan 1, 1970 00:00:000) if time is not available.

  • Returns: A list of date and time information in the following order:
    • Year
    • Month
    • Day
    • Hour
    • Minute
    • Second
    • Millisecond