RaceCapturePro Lua Scripting Examples: Difference between revisions

Line 337: Line 337:
==Enable an LED if fuel level drops below 10%==
==Enable an LED if fuel level drops below 10%==
* '''Using PWM/Analog output'''
* '''Using PWM/Analog output'''
''only available on RaceCapture/Pro MK1 and MK2''
**  Fuel sensor is on Analog 0, scaled 0-100%
**  Fuel sensor is on Analog 0, scaled 0-100%
**  LED indicator connected to PWM 0.  When fuel level drops below 10%, Analog/PWM output 0 will show 5v; 0v if fuel level is higher
**  LED indicator connected to PWM 0.  When fuel level drops below 10%, Analog/PWM output 0 will show 5v; 0v if fuel level is higher

Revision as of 17:22, 30 July 2017

How to set a script in the RaceCapture app

HowTo video: set custom script

API Reference

Complete API Reference

Data filtering

Simple RPM Filter

Got a noisy RPM signal where big spikes show up? This will reject RPM values above a sane threshold.

Important - make sure the RPM channel in the main RaceCapture/Pro config is disabled, since this virtual channel replaces it.

--sample RPM at 10Hz
setTickRate(10)

--set this value to be your sane upper limit
rpmLimit = 10000

--In the RCP config, ensure the timer channels are disabled
--we will create the virtual channel here
rpmId = addChannel( "RPM", 10, 0, 0, rpmLimit)
rpm = 0

function doRPM()
  local r = getTimerRpm(0)
  if r < rpmLimit then 
    rpm = r
  end
  setChannel(rpmId, rpm)
end


function onTick()
  doRPM()
end

Automatic logging control

Automatically Start Logging When Powered On

This script will automatically start logging the moment RaceCapture/Pro turns on

  • Note, this will create a file with an incorrect timestamp if GPS lock is not established.
    • To get a properly time-stamped file, use the GPS speed triggered approach.
function onTick()
  startLogging()
end

Automatically Start Logging based on GPS Speed

This script will automatically start logging to SD card when speed exceeds 10MPH and stop when it falls below.

function onTick()
  if getGpsSpeed() > 10 then
    startLogging()
  else
    stopLogging()
  end
end

Automatically Start Logging when engine is running

This script will automatically start logging to SD card when battery voltage shows that the engine is running

  • When battery voltage is greater than 13 volts, we assume engine is running.
  • System battery voltage is tied to the last Analog channel (8) (Note, change this to 7 if RaceCapture/Pro MK2)
function onTick()
  if getAnalog(8) > 13 then
    startLogging()
  else
    stopLogging()
  end
end

Automatically start Logging upon Launch (AutoX / Rally / Hill Climb)

This script will start Logging when a dash mounted "ARM" switch is activated via an input and G-force exceeds a threshold Given:

  • GPIO 0 configured as input and connected to dash mounted "Arm" switch
  • Default RaceCapture/Pro mounting orientation (terminal block facing forward, mounted upright)
  • G-force launch threshold is -0.1 G
  • flipping the ARM switch to 'Off' will stop logging
 setTickRate(30)
 overRevId = addChannel("OverRev", 10)


 function onTick()
  local arm = getGpio(0)
  local g = getAccel(1)
  if arm == 0 then
    stopLogging()
  end
  if arm == 1 and g < 0.1 then
    startLogging()
  end
 end

Virtual Channels (AKA Math Channels)

Averaging a fuel level reading or other sensor

This script calculates a moving average to account for fuel slosh. Assumptions:

  • Fuel level is connected to the first analog channel and is calibrated; modify the script to base the reading on other channels as appropriate.
--The real analog channel should be named
--something other than FuelLevel
fuel2Id = addChannel("FuelLevel", 10, 0, 0,100,"%")

--change this to make a bigger averaging window
maxAvg = 300 
--300 = 10 seconds averaging at 30Hz tick rate

--do not change
fuelAvg={}
fuel2Index = 1

function updateFuelAvg(value)
  local i
  if #fuelAvg == 0 then
    --initialize averaging table
    for i = 1, maxAvg do fuelAvg[i]=0 end
  end
  fuelAvg[fuel2Index] = value
  fuel2Index = fuel2Index + 1
  if fuel2Index > maxAvg then fuel2Index = 1 end
  local sum = 0
  for i = 1, #fuelAvg do
    sum = sum + fuelAvg[i]
  end
  setChannel(fuel2Id, sum / maxAvg)
end


setTickRate(30)
function onTick()
  updateFuelAvg(getAnalog(0))
end

Average two sensor values and set to a virtual channel

--10Hz update
setTickRate(10)

--Create channel: "SensorAvg"
--Sample rate: 10Hz
--Logging precision: 2 decimal points
--min/max: 0/5
--Units: "Volts"
avgId = addChannel("SensorAvg", 10, 2, 0, 5, "Volts")

function onTick()
  local a1 = getAnalog(0)
  local a2 = getAnalog(1)
  setChannel(avgId, (a1 + a2) / 2)
end

Gear Calculation

Calculate gear position based on drive train ratios

--Developed by Luther Lloyd III 8/22/14 for use by Autosport Labs Community
--Copy this text into the scripting window of Race Analyzer
--Edit the gear ratios to mathc your car
--Add another gear row if needed for 6th gear or delete extraneous ones



--below values are constants for the vehicle
local _1stGear = 3.5
local _2ndGear = 2.7
local _3rdGear = 2.0
local _4thGear = 1.4
local _5thGear = 0.9
local FinalDrive = 3.21
--diameter in inches
local TireDia = 25.0  
--allowable error of gear ratio to allow for measurement variation
local gearErr = 0.1
local rpmSpeedRatio = 0
--initialized to 0 so if it doesn't work you know
local gearPos = 0 --this is the gear channel variable

function onTick() --updates gear position every second by default

--assumes Pulse Input channel one is for the RPM signal and speed in MPH
local speed = getGpsSpeed()
local rpm = getTimerRpm(0)

--this part only works for firmware version 2.0 per the RCP page
gearId = addChannel("Gear",5)

if speed > 10 then
    --makes sure your rolling so as not to divide by 0 
    
   rpmSpeedRatio = (rpm/speed)/(FinalDrive*1056/(TireDia*3.14159))

    if ((_1stGear - rpmSpeedRatio)^2) < (gearErr^2) then gearPos = 1 end
    if ((_2ndGear - rpmSpeedRatio)^2) < (gearErr^2) then gearPos = 2 end
    if ((_3rdGear - rpmSpeedRatio)^2) < (gearErr^2) then gearPos = 3 end
    if ((_4thGear - rpmSpeedRatio)^2) < (gearErr^2) then gearPos = 4 end
    if ((_5thGear - rpmSpeedRatio)^2) < (gearErr^2) then gearPos = 5 end

else gearPos = 0 end

setChannel(gearId, gearPos) --outputs to virtual channel

end

Alerts/Notifications

Create an over-rev marker

This script will mark the datalog with an over-rev alert marker whenever RPMs are above a certain threshold. Given:

  • RPM is connected to the first Timer input channel
  • RPM over-rev condition is 8000
setTickRate(10)
overRevId = addChannel("OverRev", 10)

function onTick()
  local rpm = getTimerRpm(0)
  local overRev = 0
  if rpm > 8000 then overRev = 1 end
  setChannel(overRevId, overRev)
end

Alert driver via electro-shock if oil pressure below safe threshold

This will alert driver via a shock (using pet scat mat) if oil pressure drops below threshold while engine is running above certain RPM

Scat mat box.jpg

Script will check at 10Hz (10 times/sec) for threshold condition

Given:

  • Oil pressure on analog channel 0, and calibrated
  • Seat mounted pet scat mat installed in seat and controlled by GPIO 0 (GPIO switches ground when active)
  • GPIO 0 is configured for output mode
  • RPM is connected to timer input 0
--onTick() is called at 10Hz
setTickRate(10)
 

rpmThreshold = 2000
lowOilPressure = 15

function onTick()
  local shockDriver = 0
  if getTimerRpm(0) > rpmThreshold and getAnalog(0) < lowOilPressure then
    shockDriver = 1
  end
  setGpio(0, shockDriver)
end

Track Max RPM / Value

This script will track a channel's maximum value and set a new channel with that maximum. Given:

  • RPM is connected to the first Timer input channel
setTickRate(10)
maxRpmId = addChannel("MaxRPM", 10)
maxRpm = 0

function onTick()
  local rpm = getTimerRpm(0)
  if rpm > maxRpm then
    maxRpm = rpm
    setChannel(maxRpmId, maxRpm)
  end
end

Activate a GPIO when start finish line is crossed

This script will pulse one of the GPIO outputs when the start/finish line is detected. First, the onTick rate is set to 10hz, then setGpio() is called with the result of the call to getAtStartFinish()

setTickRate(10)

function onTick()
  if getAtStartFinish() == 1 then
    setGpio(0, 1)
  else
    setGpio(0, 0)
  end
end

or

setTickRate(10)

function onTick()
  setGpio(0, getAtStartFinish())
end

Temperature Warning Indicator Light

This script will activate an output if an analog input exceeds a threshold. It's assumed a temperature sensor is connected to the Analog input channel 0 and is calibrated.

More information: Installation Guide, Sensor Guide, Operation Guide

function onTick()
 if getAnalog(0) > 212 then
   setGpio(0, 1)
 else
   setGpio(0, 0)
 end
end

Multi warning light

A script to trigger a warning light if at least one condition occurs. This will activate the output if the engine temperature is greater than 212 or if oil pressure drops below 10.

  • Note Actual temperature and pressure sensors must be connected to the appropriate analog inputs and correctly calibrated.
--Analog 0 is engine temp, in degrees F
--Analog 1 is oil pressure, in PSI

function onTick()
 if getAnalog(0) > 212 or getAnalog(1) < 10 then
   setGpio(0, 1)
 else
   setGpio(0, 0)
 end
end

Enable an LED if fuel level drops below 10%

  • Using PWM/Analog output

only available on RaceCapture/Pro MK1 and MK2

    • Fuel sensor is on Analog 0, scaled 0-100%
    • LED indicator connected to PWM 0. When fuel level drops below 10%, Analog/PWM output 0 will show 5v; 0v if fuel level is higher
    • PWM channel settings are set to factory default
function onTick()
 local p = 0
 if getAnalog(0) < 10 then p = 100 end
 setPwmDutyCycle(0,p)
end
  • Using GPIO in output mode
    • When fuel level drops below 10%, the GPIO is activated (output is grounded). Can be used to drive a relay or other device up to 1A load
    • GPIO jumper set to output mode
    • GPIO setting in firmware set to match jumper setting
function onTick()
 local p = 0
 if getAnalog(0) < 10 then p = 1 end
 setGpio(0, p)
end

3 stage Sequential Shift Light

Activates a 3 stage sequential shift light. Also see the Sequential Shift Light project

Given:

  • RPM sensor on timer input 0


setTickRate(15)

function onTick() 
	local r = getTimerRpm(0) 
	if r > 5000 then setGpio(2,1) else setGpio(2,0) end 
	if r > 6000 then setGpio(1,1) else setGpio(1,0) end 
	if r > 7000 then setGpio(0,1) else setGpio(0,0) end
end

CAN bus scripts

Receive a CAN message on one bus and re-transmit on a different bus

setTickRate(30)
function onTick()
  id, ext, data = rxCAN(0)
  if (id ~= nil) then
    txCAN(1, id, ext, data)
  end
end

Send A CAN message with current GPS speed

Given:

  • Destination CAN device is looking for a message with ID 1234
  • Standard (11 bit) CAN identifer
  • CAN1 channel is used
function onTick()
  local speed = getGpsSpeed()
  --format the speed in a CAN message. Speed is in the first byte
  local msg = {speed} 
  txCAN(0, 1234, 0, msg)
end


Send A CAN message with a temperature value

available in future Firmware version 2.0

Given:

  • Analog 0 reads a calibrated temperature value between 0 and 255
  • Destination CAN device is looking for a message with ID 1234
  • Standard (11 bit) CAN identifer
  • CAN1 channel is used
function onTick()
  local tmp = getAnalog(0)
  local msg = {tmp}
  txCAN(0, 1234, 0, msg)
end


Use RCP as a general purpose CAN data logger

The following script will output any received CAN bus message to the log window.

  • You can access the log window by enabling polling in the script window under the RaceCapture app configuration view
  • You can also access the log window by connecting to RaceCapture/Pro from a terminal program (hyperterminal, Minicom, etc) and issuing the command: viewLog
setTickRate(30) --30Hz

function onTick()
    repeat --will drain CAN buffer on each tick
        id, e, data = rxCAN(0)
	if id ~= nil then
		print(id ..':')
		for i=1,#data do
			print(data[i] ..' ')
		end
		println('')
	end
    until id == nil
end

Receive a CAN message and set a virtual channel

Given:

  • creates a channel named "MyChannel" that logs at 10Hz
  • Sets tick rate to 10Hz
  • Receive a CAN message on CAN1 channel, with 100ms timeout
  • if data received is valid (by checking the CAN message ID is not nil), then set the virtual channel with the first element in the CAN message data
channelId = addChannel("MyChannel", 10)
setTickRate(10)

function onTick()
  id, ext, data = rxCAN(0, 100)
  if id ~= nil then
    setChannel(channelId, data[1])
  end
end

Note: To map real CAN bus data, consult your CAN bus protocol documentation for correctly mapping CAN bus data to virtual channels.

Serial Port

Read an analog sensor value and output it to the auxiliary serial port

This example reads an analog sensor and writes a string containing the value to the Auxiliary serial port. Repeats once per second.

--initialize Aux serial port to 115200, 8, N, 1
initSer(4, 115200, 8, 0, 1)

function onTick()
 value = getAnalog(0)
 writeSer(4, 'A=' ..value)
end

Read a line of serial data

This example reads a line of serial data and writes it to the internal RaceCapture log.

  • Note: You can monitor the log by enabling the log polling in the script configuration view.
--initialize Aux serial port to 115200, 8, N, 1
initSer(4, 115200, 8, 0, 1)

function onTick()
 --read a line from the aux serial port with a 100ms timeout
 value = readSer(4, 100)
 if value ~= nil then
  println('read value: ' ..value)
 end
end

Demo Scripts

RPM Sweep

This sweeps an RPM channel up and down through a pre-defined range. Edit the range at the top of the script.

-- 05 Jan 2016 RPM demo
-- F.Mirandola - B.Picasso
-- This code will show a demo RPM sweep on RaceCapturePro

thrRpmLo = 3000
 --Low RPM threshold for change direction
 
thrRpmHi = 10000
--Hi RPM threshold for change direction
incrementRpm = 300
--Step between each RPM increment/decrement, will affect the speed, higher = faster

-- Do not edit after this!!

setTickRate(10)

rpm = 0

direction = 0

rpmId = addChannel("RPM", 10, 0, 0, 10000)

function onTick()
  setChannel(rpmId, rpm)

  if (rpm<=thrRpmHi and direction == 0 ) then rpm = rpm + incrementRpm  
  	elseif (rpm>=thrRpmLo and direction == 1 ) then rpm = rpm - incrementRpm
  end

  if (rpm>thrRpmHi) then direction = 1
   	elseif (rpm<thrRpmLo) then direction = 0
  end

end

Simulating Laps

Here's a neat script that can simulate lap times and predicted times. We've used it to develop dashboard features for the app. Especially interesting is the use of the accelerometer to generate a bit of noise and variability in the data.

--Script to simulate lap and predicted times
--Without needing a moving car on race track!
--To use, disable Race Timing in RaceCapture/Pro configuration and
--use this script
etid = addChannel("ElapsedTime", 10, 4)
ltid = addChannel("LapTime", 10, 4)
ptid = addChannel("PredTime", 10, 4)
clid = addChannel("CurrentLap", 10, 0)
lcid = addChannel("LapCount", 10, 0)

et = 0 --ElapsedTime value
lt = 0 --LapTime value
pt = 0 --PredTime value
cl = 0 --CurrentLap value
lc = 0 --LapCount value

targetTime = 0.5 --target time for our fake laps

setTickRate(10)
function onTick()

local rnd = getImu(0) --use the IMU to create a random-ish number

--simulate a predicted time if we've already
--completed a lap
--rnd value makes the predicted time jiggle
if lc > 0 then 
 pt = targetTime + rnd
 setChannel(ptid, pt)
end

--increment elapsed time by 1/10 second
et = et + 0.00166666667
setChannel(etid, et)

if et > targetTime + rnd then
 lt = et
 setChannel(ltid, lt)
 et = 0
 cl = cl + 1
 setChannel(clid, cl)
 if cl > 1 then
  lc = lc + 1
  setChannel(lcid, lc)
 end
end


end