RaceCapturePro installation guide: Difference between revisions

(RaceCapture installation guide work in progress)
 
(moar content)
Line 1: Line 1:
==Overview==
==Overview==


==Terminal Block Connections==
==RaceCapture/Pro External Connections==


===Terminal block connections===
Connections Faceing Terminal Block, from left to right
Connections Faceing Terminal Block, from left to right


Line 26: Line 27:
* Frequency/pulse input 1  
* Frequency/pulse input 1  


==Expansion Port==
===Expansion Port===
The RJ45 Expansion port located next to the terminal block is provided for future sensor / control expansion.


==SD Card Slot==
===SD Card Slot===
The SD card slot is used to store datalogging sessions. 512MB to 32GB cards are supported.


==USB Port==
===USB Port===
The USB port


==LED Indicators==
===LED Indicators===
* Power LED
* Power LED
Indicates the unit is powered up (via 12v supply or USB)
Indicates the unit is powered up (via 12v supply or USB)
Line 38: Line 42:
Indicates GPS Activity. Slow flash (1Hz) indicates GPS is actively acquiring. Fast flash (5Hz for 5Hz GPS; 10Hz for 10Hz GPS) indicates GPS is locked on to satellites.
Indicates GPS Activity. Slow flash (1Hz) indicates GPS is actively acquiring. Fast flash (5Hz for 5Hz GPS; 10Hz for 10Hz GPS) indicates GPS is locked on to satellites.
* LED2
* LED2
Indicates SD card Logging Activity. The flash rate matches the channel with the highest configured logging rate.
* LED3
Indicates Telemetry Logging Activity. The flash rate matches the channel with the highest configured logging rate.
Indicates  
Indicates  
==Pushbutton==
===Pushbutton===
Press to manually start / stop a logging session. Note this may be overridden by any on-board scripts that may automatically start or stop logging.


==Communication Ports==
===Communication Ports===
The communication ports a standard RS232 serial connection with power (up to 5v at 1.5A)
* Port 1
* Port 1
Used for telemetry expansion module
Used for telemetry expansion module
* Port 2
* Port 2
used for GPS module
used for GPS module
==Internal Switches / Jumpers==
===4 position DIP switch (SW1)===
This switch bank configures the 4 outputs for Analog or Frequency/PWM mode. To enable analog mode for a particular output channel, slide the switch for the selected channel to the 'on' position. For Frequency/PWM mode slide the switch to 'off'.
===GPIO configuration jumpers===
The array of jumper blocks configures the 3 GPIO channels for either digital input or output. To configure a particular channel, move the jumper to either the IN position (for input) or OUT (for output)
* When configured for input, the channel accepts a 0-5v input.
* When configured for output, the channel provides an open-drain output that can drive 1A and is thermal / over-current protected with inductive load clamping. When the output is deactivated, a 1K ohm pull-up to +5v is present.

Revision as of 05:14, 28 September 2012

Overview

RaceCapture/Pro External Connections

Terminal block connections

Connections Faceing Terminal Block, from left to right

  • Ground/Common
  • +12v
  • Analog/Frequency out 4
  • Analog/Frequency out 3
  • Analog/Frequency out 2
  • Analog/Frequency out 1
  • +5V Voltage reference
  • Analog input 7
  • Analog input 6
  • Analog input 5
  • Analog input 4
  • Analog input 3
  • Analog input 2
  • Analog input 1
  • General purpose input/output 3
  • General purpose input/output 2
  • General purpose input/output 1
  • Frequency/pulse input 3
  • Frequency/pulse input 2
  • Frequency/pulse input 1

Expansion Port

The RJ45 Expansion port located next to the terminal block is provided for future sensor / control expansion.

SD Card Slot

The SD card slot is used to store datalogging sessions. 512MB to 32GB cards are supported.

USB Port

The USB port

LED Indicators

  • Power LED

Indicates the unit is powered up (via 12v supply or USB)

  • LED1

Indicates GPS Activity. Slow flash (1Hz) indicates GPS is actively acquiring. Fast flash (5Hz for 5Hz GPS; 10Hz for 10Hz GPS) indicates GPS is locked on to satellites.

  • LED2

Indicates SD card Logging Activity. The flash rate matches the channel with the highest configured logging rate.

  • LED3

Indicates Telemetry Logging Activity. The flash rate matches the channel with the highest configured logging rate.

Indicates

Pushbutton

Press to manually start / stop a logging session. Note this may be overridden by any on-board scripts that may automatically start or stop logging.

Communication Ports

The communication ports a standard RS232 serial connection with power (up to 5v at 1.5A)

  • Port 1

Used for telemetry expansion module

  • Port 2

used for GPS module

Internal Switches / Jumpers

4 position DIP switch (SW1)

This switch bank configures the 4 outputs for Analog or Frequency/PWM mode. To enable analog mode for a particular output channel, slide the switch for the selected channel to the 'on' position. For Frequency/PWM mode slide the switch to 'off'.

GPIO configuration jumpers

The array of jumper blocks configures the 3 GPIO channels for either digital input or output. To configure a particular channel, move the jumper to either the IN position (for input) or OUT (for output)

  • When configured for input, the channel accepts a 0-5v input.
  • When configured for output, the channel provides an open-drain output that can drive 1A and is thermal / over-current protected with inductive load clamping. When the output is deactivated, a 1K ohm pull-up to +5v is present.