SensorX: Difference between revisions

(Created page with "=SensorX board= Image:sensorX_board.png SensorX is a breakout board that provides multiple ground and 5v reference signals for up to 7 sensors, including spots for pull-...")
 
(initial content)
Line 7: Line 7:
==Wiring sensors==
==Wiring sensors==


Wire
Sensors are connected to the right side of the SensorX board in groups of 7 sensor connections.
 
===Passive / Thermistor Temperature Sensors===
Most passive thermistor-based temperature sensors require a pull-up resistor to provide the variable voltage needed for the analog input for RaceCapture. The SensorX board provides locations to install pull-up resistors to ease the installation of these types of sensors.
 
To install the pull-up resistor, place one of the included 2.2K resistors in the diagonally placed location next to each RaceCapture input (1 - 7). Solder the resistor in place and clip the leads on the back, ensuring they are flush.
 
Once the pullup resistor is in place, you can wire up the two leads of the temperature sensor to the Ground (GND) and Input (IN_X) connections of the SensorX board.
* Ensure a good solder joint and clip the leads flush.
* You do not need to wire up the 5v connection since the built-in pull up resistor provides the voltage that completes the voltage divider circuit.
 
[[Image:sensorx_temperature_sensor.jpg]]
 
===Active Sensors===
Active type sensors require 3 connections:
 
* Ground
* 5v
* Output signal
 
Wire up the 3 connections to the sensor by connecting Ground (GND_X), 5v (5V_X) and Input (IN_X).
 
* Ensure a good solder joint and clip the leads flush.
 
[[Image:sensorx_active_sensor.jpg]]
 
==Connecting to RaceCapture inputs==
Once the sensors are connected to the Sensor Side of the SensorX board, you can route individual wires to the Ground, 5v reference and analog inputs of RaceCapture.
 
[[Image:sensorx_racecapture_connection.jpg]]
 
==Final installation==
When testing is complete, you can slip the SensorX board inside heat shrink tubing and bundle it in-line with the rest of your wiring harness for a clean installation.
[[Image:sensorx_heat_shrink.jpg]]

Revision as of 23:11, 29 March 2016

SensorX board

SensorX board.png

SensorX is a breakout board that provides multiple ground and 5v reference signals for up to 7 sensors, including spots for pull-up resistors for passive, two wire temperature sensors. It's specifically designed to be bundled in-line with your wiring harness and covered in heat-shrink tubing when fully assembled.

Wiring sensors

Sensors are connected to the right side of the SensorX board in groups of 7 sensor connections.

Passive / Thermistor Temperature Sensors

Most passive thermistor-based temperature sensors require a pull-up resistor to provide the variable voltage needed for the analog input for RaceCapture. The SensorX board provides locations to install pull-up resistors to ease the installation of these types of sensors.

To install the pull-up resistor, place one of the included 2.2K resistors in the diagonally placed location next to each RaceCapture input (1 - 7). Solder the resistor in place and clip the leads on the back, ensuring they are flush.

Once the pullup resistor is in place, you can wire up the two leads of the temperature sensor to the Ground (GND) and Input (IN_X) connections of the SensorX board.

  • Ensure a good solder joint and clip the leads flush.
  • You do not need to wire up the 5v connection since the built-in pull up resistor provides the voltage that completes the voltage divider circuit.

File:Sensorx temperature sensor.jpg

Active Sensors

Active type sensors require 3 connections:

  • Ground
  • 5v
  • Output signal

Wire up the 3 connections to the sensor by connecting Ground (GND_X), 5v (5V_X) and Input (IN_X).

  • Ensure a good solder joint and clip the leads flush.

File:Sensorx active sensor.jpg

Connecting to RaceCapture inputs

Once the sensors are connected to the Sensor Side of the SensorX board, you can route individual wires to the Ground, 5v reference and analog inputs of RaceCapture.

File:Sensorx racecapture connection.jpg

Final installation

When testing is complete, you can slip the SensorX board inside heat shrink tubing and bundle it in-line with the rest of your wiring harness for a clean installation. File:Sensorx heat shrink.jpg