RaceCapture/Pro MK1 firmware upgrade: Difference between revisions

(clarified instructions for GPS camera detector driver)
No edit summary
Line 1: Line 1:
==Upgrading RaceCapture/Pro firmware==
==Upgrading RaceCapture/Pro firmware==


===Steps for ROM bootloader===
Your RaceCapture/Pro unit ships with firmware pre-installed and should work out of the box. You'll only need to follow these instructions when you want to access new features or apply bug fixes.
 
===Installing new Firmware===
 
 
====Download the new firmware and flash utility from [[RaceCapturePro_Downloads|Downloads]] section====
Place the downloaded files in a known directory on your computer (e.g. RaceCapturePro-1.1.6.elf where 1.1.6 denotes the version number)
 
====Open a command prompt====
 
Open a command prompt and navigate to the directory where you placed the downloaded files.
 
e.g. for Windows:
cd c:\firmware
 
====Connect RaceCapture/Pro====
 
 
 
 
 
 
===Steps for Factory ROM bootloader===
 
This is the backup mechanism for re-flashing firmware and should 'only' be used when the primary firmware upgrading mechanism fails.


====Prerequisite====
====Prerequisite====
Line 42: Line 66:
* Slide the circuit board back in to the enclosure, aligning it with the holes in the end plate. It may be easier in some cases to remove both end plates to enable connectors/LEDs/button to fit into the end plate cut-outs. Ensure the smaller components, like LEDs fit correctly into their respective locations.   
* Slide the circuit board back in to the enclosure, aligning it with the holes in the end plate. It may be easier in some cases to remove both end plates to enable connectors/LEDs/button to fit into the end plate cut-outs. Ensure the smaller components, like LEDs fit correctly into their respective locations.   
* Slide mounting rails into place before installing 2nd end plate. Replace screws.
* Slide mounting rails into place before installing 2nd end plate. Replace screws.
===Steps for SD card upgrade===
We are developing a more convenient upgrade via SD card. Watch this space for updates.

Revision as of 03:38, 8 March 2013

Upgrading RaceCapture/Pro firmware

Your RaceCapture/Pro unit ships with firmware pre-installed and should work out of the box. You'll only need to follow these instructions when you want to access new features or apply bug fixes.

Installing new Firmware

Download the new firmware and flash utility from Downloads section

Place the downloaded files in a known directory on your computer (e.g. RaceCapturePro-1.1.6.elf where 1.1.6 denotes the version number)

Open a command prompt

Open a command prompt and navigate to the directory where you placed the downloaded files.

e.g. for Windows:

cd c:\firmware

Connect RaceCapture/Pro

Steps for Factory ROM bootloader

This is the backup mechanism for re-flashing firmware and should 'only' be used when the primary firmware upgrading mechanism fails.

Prerequisite

Install the Atmel SAM-BA flash utility. This is a small application that performs the firmware write.

Save RaceCapture/Pro configuration

The firmware upgrade process resets the configuration to factory defaults. To preserve the settings and any scripts you have running on your unit, save the active configuration using the RaceCapture/Pro configuration application.

Remove board from enclosure

Remove 4 screws from either end of the RaceCapture/Pro enclosure and slide the circuit board out. Place the board on a non-conductive surface.

Load Factory ROM Bootloader

  • Locate the 'test' button on the circuit board. If there is no test button installed, bridge the pads where the test button would be installed with a short jumper wire.
  • Press the test button (or short the pads), then apply power to the RaceCapture/Pro board using the USB cable. Hold the button for 20 seconds
    • (This will write back the ROM factory bootloader into flash memory)
  • Release the button and disconnect power.

Flash firmware

  • Re-apply power using the USB cable.
  • If you are prompted for drivers, install the drivers provided under the SAM-BA directory (typically found under C:\Program Files\Atmel\sam-ba_2.12\drv)
  • Once the drivers are loaded, you should see the device listed under Windows Device Manager - Ports as 'AT91 USB to Serial Converter'
    • If you do not see the board recognized this way, ensure you have the Atmel SAM-BA flash utility and drivers correctly installed. If you still have problems, repeat the previous step of loading the factory ROM bootloader.
    • If the board comes up as 'GPS Camera Detector' then Windows installed the wrong drivers. Use these instructions to remove the incorrect drivers before proceeding.
  • Run the SAM-BA flash utility.
    • Under 'Select the connection', select board as identified by Device Manager. The board will be defined as '\USBserial\COMXX' where COMXX is the COM port assigned in Device Manager.
    • Under 'Select your board', select 'at91sam7s256-ek'.
  • On the Flash tab, under 'Download/Upload File' select button next to 'Send File Name'. Browse to the RaceCapture/Pro firmware, which will be a file ending in .bin (e.g. RaceCapturePro-0.0.2.bin)
  • Click the 'Send File' option in the program.
    • If prompted to 'Unlock' regions, click yes.
  • You should observe the firmware flashing progress in the window. When complete, you can remove power to RaceCapture/Pro.

Verify Firmware

  • Re-Apply power to RaceCapture/Pro. In Windows, you should see the RaceCapture/Pro device listed under Ports; note the COM port number assigned. In Linux, you should see a device under /dev/ttyACM0. The 'dmesg' command should have information about the device.
  • Using the configuration application, select the appropriate port, connect to the RaceCapture/Pro and verify the current firmware version.
  • Restore any previously saved configuration.

Re-assemble RaceCapture/Pro

  • Slide the circuit board back in to the enclosure, aligning it with the holes in the end plate. It may be easier in some cases to remove both end plates to enable connectors/LEDs/button to fit into the end plate cut-outs. Ensure the smaller components, like LEDs fit correctly into their respective locations.
  • Slide mounting rails into place before installing 2nd end plate. Replace screws.