ShiftX2: Difference between revisions

No edit summary
 
(76 intermediate revisions by the same user not shown)
Line 1: Line 1:
=Introduction=
=Introduction=
(Introduction about ShiftX2)


=Scripts=
==Parts in the Kit==
In the kit you will receive:
* ShiftX2 module
* 4 wire pigtail
* Acrylic enclosure
* Mounting screws with o-rings
 
[[Image:ShiftX2_components.jpg|800px]]
 
==Dimensions==
* ShiftX2 bare board: 143 x 85mm (5.6 x 3.27 inches)
* ShiftX2 enclosure: 172 x 18 x 12.7 mm (6.x8 x 0.71 x 0.5 inches)
 
=Installation=
ShiftX2 is designed to be surface mounted with the included enclosure, or it can be embedded into your dashboard in a custom installation.
 
==Assembling the enclosure==
* plug the wiring pigtail into the socket on ShiftX2.  The plug is keyed to insert in one direction, with the red wire to the left.
[[Image:ShiftX2_pigtail.jpg|800px]]
 
* Thread the pigtail through the hole in the bottom layer of the acrylic enclosure (1/8" black plastic plate).
[[Image:ShiftX2_wiring_base.jpg|800px]]
 
* Place ShiftX2 onto the bottom layer, stack the 1/4" middle frame on top, with the clearance notch over the connector, and finally the top clear lens.
[[Image:ShiftX2_top_lens.jpg|800px]]
 
* Place the two o-rings onto the mounting screws - these cushion the mounting points of ShiftX2 - and place them into mounting holes, passing through all 3 layers of the enclosure.
[[Image:ShiftX2_screws.jpg|800px]]
 
[[Image:ShiftX2_assembled.jpg|800px]]
 
==Mounting ShiftX2==
Mount ShiftX2 to your dashboard surface using the following template:
((picture))
 
* '''Note:''' Ensure the hole for the wiring is deburred and has no sharp edges.
 
Attach ShiftX2 with the mounting screws and tighten until snug and the o-rings are compressed. 
 
* '''Note''': '''Do not overtighten''' to prevent cracking of the acrylic enclosure.
 
==Wiring==
===Pinout===
Orientation is left to right looking into board connector:
 
{| class="wikitable" | width="600px"
|-
! Color
! Assignment
! Notes
|-
| Red
| 9-12v Power
| Connect this to switched ignition power. 0.5A max consumption.
|-
| Black
| CAN High
|
|-
| Yellow
| CAN Low
|
|-
| White
| Ground
|
|}
 
===Integration with RaceCapture / PodiumConnect===
 
We recommend connecting ShiftX2 to CAN2 of your RaceCapture or PodiumConnect system.
 
====Direct Wiring====
 
For RaceCapture/Pro MK3, RaceCapture/Apex and PodiumConnect, we recommend direct wiring to the CAN bus connections provided by your system.
 
[[Image:shiftx2_direct_wiring.png]]
 
For RaceCapture/Pro MK2 or RaceCapture/Track MK2 using the RJ45 connector, you can use a commonly available RJ45 splitter and RJ45 network-style extension cables to conveniently connect both OBDII and ShiftX2 on the same connector.  With ShiftX2 on CAN2, the OBDII port is free to continue to use CAN1, and ShiftX2 will receive power from the OBDII port.
 
[[Image:shiftx2_with_splitter.png]]
 
Suggested parts:
 
* RJ45 Splitter [https://www.amazon.com/gp/product/B078TGG5YC "Hub" shaped]
* RJ45 network cable [https://www.amazon.com/s/?ref=nb_sb_noss?url=search-alias%3Delectronics&field-keywords=rj45+flat+6+foot+cable+black&rh=n%3A172282%2Ck%3Arj45+flat+6+foot+cable+black Flat style] [https://www.amazon.com/s/?ref=nb_sb_noss_2?url=search-alias%3Delectronics&field-keywords=rj45+6+foot+cable+black+round&rh=n%3A172282%2Ck%3Arj45+6+foot+cable+black+round round style]
** '''Note''' Any standard CAT5 or CAT6 patch cable should work, so long as it is not a cross-over cable.
 
=====Patching the RJ45 cable to ShiftX2=====
 
You will need to splice ShiftX2 to the conductors of the patch cable.  Start by snipping the RJ45 connector off the end of a patch cable, and then expose the individual wires.
 
[[file:Rj45labeled.jpg|500px]]
 
{| class="wikitable" style="text-align:center; width:700px; height:200px;"
|+ RJ45 power and CAN connection pinout
|-
! ShiftX2 connection
! RaceCapture Connection
! CAT5 EIA-T568B RJ45 cable
|-
| Red
| +12v
| Brown
|-
| White
| Ground
| Orange/White
|-
| No Connection
| CAN 1 High
| Orange
|-
| No Connection
| CAN 1 Low
| Green/White
|-
| Black
| CAN 2 High
| Blue
|-
| Yellow
| CAN 2 Low
| Blue/White
|}
'''Note:''' These color codes assume EIA-T568B RJ45 cable (check printing on the cable to confirm)
 
===CAN Termination===
CAN termination is enabled by default.  To disable termination, cut the '''CAN Term''' jumper on the bottom of ShiftX2.
 
* '''Note''': the termination jumper is located on the bottom side of the ShiftX2 circuit board, on the right side of the board when the push button is on the left.  It is labeled '''CAN TERM'''
 
There will be a small trace between the two square pads - cut the trace carefully using a razor, or the sharp tip of a small jewler's screwdriver  paying close attention to not damage adjacent traces.  To restore the jumper, solder a bridge between the pads.
 
==Powering and Connecting to RaceCapture==
===Power===
To power ShiftX2, connect the '''red''' wire to '''switched 12v''', and the '''white''' wire to '''Ground'''. 
* '''Note:''' You can use the same circuit for your RaceCapture system so they power up simultaneously.
 
===CAN bus connections===
Connect the '''black''' wire to '''CAN High''', and the '''yellow''' wire to '''CAN Low'''.
* '''Note:''' You can choose either CAN1 or CAN2 to drive ShiftX2. The CAN bus can be defined in the script you use to control ShiftX2.
 
=Using ShiftX2=
The LEDs and display on ShiftX2 are controlled by RaceCapture's Lua scripting capabilities. Built-in functions provide access to ShiftX2's capabilities.  See the [[RaceCapturePro_Lua_Scripting#ShiftX2.2F3_control|ShiftX2 Lua scripting reference]] for additional details.
 
==Compatibility==
ShiftX2 works with the following devices:
* RaceCapture/Pro MK2
* RaceCapture/Pro MK3
* RaceCapture/Apex
* RaceCapture/Track MK2
* PodiumConnnect
 
==Firmware Requirements==
ShiftX2 requires RaceCapture/PodiumConnect firmware 2.15.0 or higher. [http://podium.live/software Download the latest firmware]
 
==Navigation Buttons==
Once ShiftX2 is powered and connected via CAN bus to your RaceCapture system, the left button will automatically trigger a page navigation on the RaceCapture app dashboard.
 
The following scripts assume ShiftX2 is connected to the 2nd CAN bus, and is the first ShiftX2 on the bus (ADR1 jumper default setting)


==Disco Lights Demo==
==Disco Lights Demo==
This is a test script that exercises all of the LEDs on ShiftX2. Use this as a first time test.  
This is a test script that exercises all of the LEDs on ShiftX2. You can use this as a first time test, as it does not rely on any sensors.  


===Script===
===Script===
Copy and paste this entire script into the scripting window, replacing any existing script.  
Copy and paste this entire script into the scripting window, replacing any existing script.  
<pre>
<pre>
setTickRate(10)
function rndc()
  return math.random(0,255)
end
function onTick()
  for i=0,9,1 do
    sxSetLed(i,1,rndc(),rndc(),rndc(),0)
  end
  -- ascii characters between 0 and 9
  sxSetDisplay(0, math.random(0,9))
end
</pre>
==Sequential shift light==
This script configures just a sequential shift light.
===Script===
Copy and paste this entire script, replacing any existing script:
* Default is reading RPM via OBDII. You can change to direct RPM input in the script.
<pre>
setTickRate(30)
-- Set ShiftX2 configuration parameters with default parameters
-- orientation: 0=normal, 1=inverted (display above LED bar)
-- brightness: 0-100%, 0 = auto brightness
-- can bus: 0=CAN1, 1=CAN2
sxSetConfig(0,0,1)
--config shift light
sxCfgLinearGraph(0,0,0,7000) --left to right graph, smooth style, 0 - 7000 RPM range
sxSetLinearThresh(0,0,1000,0,255,0,0) --green at 3000 RPM
sxSetLinearThresh(1,0,5000,255,255,0,0) --yellow at 5000 RPM
sxSetLinearThresh(2,0,6000,255,0,0,10) --red+flash at 6000 RPM
function onTick()
function onTick()
--implement me
  sxUpdateLinearGraph(getChannel("RPM"))
end
end
</pre>
</pre>


==Shift Light + Twin Alert Example==
==Shift Light + Twin Alert Example==
(this script is a complete example that does a sequential shift light + two alert indicators)
This script shows a more complete example that demos a sequential shift light + two alerts.
 
Assumptions:
* Engine Temperature on the 1st alert LED, connected to first analog channel
* Oil Pressure on the 2nd alert LED, connected to second analog channel
 
Edit the script to change the analog channels you want to monitor.


===Script===
===Script===
Copy and paste this entire script into the scripting window, replacing any existing script.  
Copy and paste this entire script into the scripting window, replacing any existing script.  
<pre>
<pre>
setTickRate(30)
-- Set ShiftX2 configuration parameters with default parameters
-- orientation: 0=normal, 1=inverted (display above LED bar)
-- brightness: 0-100%, 0 = auto brightness
-- can bus: 0=CAN1, 1=CAN2
sxSetConfig(0,0,1)
--config shift light
sxCfgLinearGraph(0,0,0,7000) --left to right graph, smooth style, 0 - 7000 RPM range
sxSetLinearThresh(0,0,1000,0,255,0,0) --green at 3000 RPM
sxSetLinearThresh(1,0,5000,255,255,0,0) --yellow at 5000 RPM
sxSetLinearThresh(2,0,6000,255,0,0,10) --red+flash at 6000 RPM
--configure first alert (right LED) as engine temperature (F)
sxSetAlertThresh(0,0,205,255,255,0,0) --yellow warning at 205F
sxSetAlertThresh(0,1,225,255,0,0,10) -- red flash at 225F
--configure second alert (left LED) as oil pressure (PSI)
sxSetAlertThresh(1,0,0,0,0,255,10) --red flash below 15 psi
sxSetAlertThresh(1,1,15,255,255,0,5) --yellow flash 15-20 PSI
sxSetAlertThresh(1,2,20,0,0,0,0) --above 20, no alert
function onTick()
function onTick()
--implement me
  --update RPM
  sxUpdateLinearGraph(getChannel("RPM"))
 
  --update engine temp alert
  sxUpdateAlert(0, getChannel("EngineTemp"))
 
  --update oil pressure alert
  sxUpdateAlert(1, getChannel("OilPress"))
end
end
</pre>
</pre>
Line 32: Line 267:
A bar extends left or right from the center of the linear graph:
A bar extends left or right from the center of the linear graph:
* Green bar extending to the right indicates you're beating the best time
* Green bar extending to the right indicates you're beating the best time
* Orange bar extending to the left means you're falling behind.  
* Red bar extending to the left means you're falling behind.
* When you're close to the best time, the center blue LED illuminates.
 
 
'''Notes:'''
* The script is designed for a +/- 10 second maximum delta - so if you're ahead or behind by 10 seconds, the linear graph will be fully illuminated center-right, or center-left.
* You will need to complete a a full lap to train the predictive timer before the graph will update.


===Script===
===Script===
Copy and paste this entire script into the scripting window, replacing any existing script.  
Copy and paste this entire script into the scripting window, replacing any existing script.  
<pre>
<pre>
-- Predictive time visualizer
--save best lap time
bestTime = 0
-- Set ShiftX2 configuration parameters with default parameters
-- orientation: 0=normal, 1=inverted (display above LED bar)
-- brightness: 0-100%, 0 = auto brightness
-- can bus: 0=CAN1, 1=CAN2
sxSetConfig(0,0,1)
--config shift light
sxCfgLinearGraph(1,0,0,200) --center-out graph, linear style, +/- 10.0 seconds in 0.1 sec resolution
sxSetLinearThresh(0,0,0,255,0,0,0) --red if you're falling behind best lap
sxSetLinearThresh(1,0,80,0,0,255,0) --blue if you're close to best lap
sxSetLinearThresh(2,0,110,0,255,0,0) --green if you're beating best lap
setTickRate(30)
function onTick()
function onTick()
--implement me
  local predTime = getPredTime()
 
  local timeDiff = (bestTime - predTime) * 60
  -- rail values
  timeDiff = math.max(timeDiff, -10)
  timeDiff = math.min(timeDiff, 10)
  --scale values from +/- 10 sec to a 0-200 scale
  timeDiff = (timeDiff + 10) * 10
 
  sxUpdateLinearGraph(timeDiff)
 
  --update best lap time if an updated lap time is available
  local lastLapTime = getLapTime()
  if lastLapTime < bestTime or bestTime == 0 then bestTime = lastLapTime end
end
end
</pre>
</pre>
Line 46: Line 321:


===How it works===
===How it works===
The script configures the linear graph, then reads an analog channel and updates the graph with the current value. In this case, the value represents boost level measured from a MAP sensor.  
The script configures the linear graph, then reads an analog channel and updates the graph with the current value. In this case, the value represents boost level measured from a MAP sensor.
 
===Assumptions===
* MAP sensor channel is on the first Analog channel, and reads in KPa - typically 0-255.  You can also connect this to the MAP reading on OBDII (PID 11)


===Script===
===Script===
Copy and paste this entire script into the scripting window, replacing any existing script.  
Copy and paste this entire script into the scripting window, replacing any existing script.  
<pre>
<pre>
setTickRate(30)
-- Set ShiftX2 configuration parameters with default parameters
-- orientation: 0=normal, 1=inverted (display above LED bar)
-- brightness: 0-100%, 0 = auto brightness
-- can bus: 0=CAN1, 1=CAN2
sxSetConfig(0,0,1)
--config shift light
sxCfgLinearGraph(0,0,0, 20) --left to right graph, linear style, 0 - 20 PSI boost
sxSetLinearThresh(0,0,0,0,255,0,0) --green starting at no boost
sxSetLinearThresh(1,0,10,255,255,0,0) --yellow starting at 10 PSI boost
sxSetLinearThresh(2,0,15,255,0,0,10) --red+flash at 15 PSI boost
function onTick()
function onTick()
--implement me
  local map = getChannel("MAP")
  if map ~= nil then
    --convert to PSI boost
    local boost = math.max(map - 100, 0) * .145038
    sxUpdateLinearGraph(boost)
  end
end
end
</pre>
</pre>


==Only Alerts==
=Manual control of ShiftX2=
This script enables 3 alert channels:
You can obtain low level control ShiftX2 by sending it direct CAN messages in Lua scripting. This is primarily useful if controlling a second ShiftX2 running on an alternate CAN ID.
* Left alert for oil pressure
 
* Right alert for engine temperature
* '''Note''': The built-in firmware support for ShiftX2 is focused on controlling one ShiftX2 in your system.  - you can use a combination of the built-in functions to control the primary ShiftX2, and then direct CAN control for the second unit.
* Center alert for Air/Fuel ratio


===How it works===
Example starter script that shows how to directly control ShiftX2:
The script configures the left and right alert indicators, then configures the center graph to visualize safe and dangerous AFR ranges.  During operation, the analog channels for oil pressure and engine temperature are read and updates the alert indicators. The AFR channel is read and updates the linear graph.


===Script===
Copy and paste this entire script into the scripting window, replacing any existing script.
<pre>
<pre>
function onTick()
-- What CAN bus ShiftX2 is connected to. 0=CAN1, 1=CAN2
--implement me
sxCan = 0
 
-- 0=first ShiftX2 on bus, 1=second ShiftX2 (if ADR1 jumper is cut)
sxId=0
 
--how often ShiftX2 is updated
tickRate=30
 
--Brightness, 0-100. 0=automatic brightness
sxBright=0
 
function sxOnUpdate()
  --add your code to update ShiftX2 alerts or linear graph during run time.
  --Runs continuously based on tickRate.
 
end
 
function sxOnInit()
  --add your code for configuring ShiftX2. Runs once during startup
 
end
 
function sxOnBut(b)
  --called if the button state changes
  println('button: ' ..b)
end
 
---ShiftX2 functions
--===============
--Reference. Delete me to save space
--===============
 
--function sxSetLed(index,length,red,green,blue,flash)
--Set an individual LED
--index: LED index, starting at 0
--length: number of LEDs to set at once
--red: Red value (0-255)
--green: Green value (0-255)
--blue: Blue value(0-255)
--flashHz: Flash rate, in Hz; 0=no flash
 
--sxSetLinearThresh(thresholdId,segmentLength,thresholdValue,red,green,blue,flashHz)
--Setup a threshold for the linear graph
--thresholdId: Threshold ID to set. from 0-4. define in ascending order.
--segmentLength: Length of the segment when in stepped graph mode. ignored for smooth mode.
--thresholdValue: Value for this threshold.
--red: Red value (0-255)
--green: Green value (0-255)
--blue: Blue value (0-255)
--flashHz: Flash rate, in Hz; 0=no flash
 
--sxSetAlertThresh(alertId,thresholdId,thresholdValue,red,green,blue,flashHz)
--Setup a threshold for an alert indicator
--alertId: Id of the alert to configure
--thresholdId: Threshold ID to set. from 0-4. define in ascending order.
--thresholdValue: Value for this threshold.
--red: Red value (0-255)
--green: Green value (0-255)
--blue: Blue value (0-255)
--flashHz: Flash rate, in Hz; 0=no flash
 
--sxSetAlert(alertId,red,green,blue,flashHz)
--Directly sets an alert indicator
--alertId: Alert Id to set
--red: Red value (0-255)
--green: Green value (0-255)
--blue: Blue value (0-255)
--flashHz: Flash rate, in Hz; 0=no flash
 
--sxUpdateAlert(alertId,currentValue)
--Updates Current alert value, using the previously configured thresholds
--alertId: Alert Id to set
--currentValue: Updated value
 
--sxCfgLinearGraph(renderStyle,linearStyle,lowRange,highRange)
--Configures the linear graph
--renderStyle: 0=left->right, 1=center,2=right->left
--linearStyle: 0=smooth/interpolated, 1=stepped
--lowRange: low range of the graph
--highRange: high range of the graph (ignored if stepped linear style)
 
--sxUpdateLinearGraph(currentValue)
--Updates the linear graph value, using the previously configured thresholds
--currentValue: Updated value
--===============
--End reference
--===============
 
function sxSetLed(i,l,r,g,b,f)
  sxTx(10,{i,l,r,g,b,f})
end
 
function sxSetLinearThresh(id,s,th,r,g,b,f)
  sxTx(41,{id,s,spl(th),sph(th),r,g,b,f})
end
 
function sxSetAlertThresh(id,tid,th,r,g,b,f)
  sxTx(21,{id,tid,spl(th),sph(th),r,g,b,f})
end
 
function setBaseConfig(bright)
  sxTx(3,{bright})
end
 
function sxSetAlert(id,r,g,b,f)
  sxTx(20,{id,r,g,b,f})
end
 
function sxUpdateAlert(id,v)
  if v~=nil then sxTx(22,{id,spl(v),sph(v)}) end
end
 
function sxCfgLinearGraph(rs,ls,lr,hr)
  sxTx(40,{rs,ls,spl(lr),sph(lr),spl(hr),sph(hr)})
end
 
function sxUpdateLinearGraph(v)
  sxTx(42,{spl(v),sph(v)})
end
 
function sxInit()
  println('config shiftX2')
  setBaseConfig(sxBright)
  if sxOnInit~=nil then sxOnInit() end
end
 
function sxChkCan()
  id,ext,data=rxCAN(sxCan,0)
  if id==sxCanId then sxInit() end
  if id==sxCanId+60 and sxOnBut~=nil then sxOnBut(data[1]) end
end
 
function sxProcess()
  sxChkCan()
  if sxOnUpdate~=nil then sxOnUpdate() end
end
 
function sxTx(offset, data)
  txCAN(sxCan, sxCanId + offset, 1, data)
  sleep(10)
end
end
</pre>


==ShiftX2 starter script==
function spl(v) return bit.band(v,0xFF) end
Use this as a starter for your own custom script
function sph(v) return bit.rshift(bit.band(v,0xFF00),8) end


<pre>
function onTick()
function onTick()
--implement me
  sxProcess()
end
end
sxCanId = 0xE3600 + (256 * sxId)
println('shiftx2 base id ' ..sxCanId)
setTickRate(tickRate)
sxInit()
</pre>
</pre>


Line 94: Line 531:


CAN base ID is 0xE3600 (931328)
CAN base ID is 0xE3600 (931328)
 
If the device supports hardware configurable ID offsets, such as via DIP switches or breakable jumpers, each incremental offset will add 256 to the base ID.
====Altering the Base ID====
Cutting the jumper ADR1 will add 256 to the base ID, allowing up to two ShiftX2 displays on the same CAN bus.
 
* '''Note''': the ADR1 jumper is located on the bottom side of the ShiftX2 circuit board, on the left side of the board when the push button is on the left. It is labeled "ADR1"
 
There will be a small trace between the two square pads - cut the trace carefully using a razor, or the sharp tip of a small jewler's screwdriver  paying close attention to not damage adjacent traces.  To restore the jumper, solder a bridge between the pads.
 
===CAN Baud rate===
 
500K and 1MB rates are supported.
 
500K is enabled by default; cut the jumper ADR2 on the bottom of ShiftX2 to enable 1MB.
 
* '''Note''': the ADR2 jumper is located on the bottom side of the ShiftX2 circuit board, on the left side of the board when the push button is on the left. It is labeled "ADR2"
 
There will be a small trace between the two square pads - cut the trace carefully using a razor, or the sharp tip of a small jewler's screwdriver  paying close attention to not damage adjacent traces.  To restore the jumper, solder a bridge between the pads.


===Configuration / Runtime Options===
===Configuration / Runtime Options===
Line 133: Line 585:
| Patch Version
| Patch Version
| Firmware patch version number
| Firmware patch version number
|}
====Reset Device====
Resets the device, loading defaults
'''CAN ID:''' Base + 1
{| class="wikitable" | width="600px"
|-
! Offset
! What
! Value
|-
| colspan="3" | (no data)
|}
|}


Line 184: Line 623:
| 0
| 0
| Brightness
| Brightness
|  0 - 100 (0=automatic brightness)
|  0 - 100; 1 = dimmest; 100 = brightest; 0 = automatic brightness control using built-in light sensor.
|-
| 1
| Automatic brightness scaling (Optional)
0-255; default=51. adjust this value to adjust the relative gain of the built-in light sensor when in automatic brightness mode.
|}
|}


Line 260: Line 703:


Notes:
Notes:
* Threshold value must be > 0 to be valid
* If the current value is greater than the last threshold, then the last threshold is selected.
* Alerts are processed in descending order by Threshold ID, where:
* The first threshold may have a threshold value >= 0; remaining thresholds must be > 0
** The threshold is selected where the threshold is > 0 and current value is >= threshold and < than the next threshold
** If the current value is greater than the last threshold, then the last threshold is selected.  
** If the current value is less than the first threshold, then the alert indicator is disabled.


'''CAN ID:''' Base + 21
'''CAN ID:''' Base + 21
Line 394: Line 834:
====Set Linear Graph Threshold====
====Set Linear Graph Threshold====
Configures a linear threshold. Up to 5 thresholds can be configured
Configures a linear threshold. Up to 5 thresholds can be configured
Notes:
* If the current value is greater than the last threshold, then the last threshold is selected.
* The first threshold may have a threshold value >= 0; remaining thresholds must be > 0


'''CAN ID:''' Base + 41
'''CAN ID:''' Base + 41
Line 434: Line 878:
|  0 - 10 (0 = full on)
|  0 - 10 (0 = full on)
|}
|}
====Update Current Linear Graph Value====
====Update Current Linear Graph Value====


Line 452: Line 897:
| Value (high byte)
| Value (high byte)
|
|
|}
===Notifications===
Notifications related to events broadcasted from ShiftX2
====Button State====
Indicates a change in the button state
'''CAN ID:''' Base + 60
{| class="wikitable" | width="600px"
|-
! Offset
! What
! Value
|-
| 0
| Button state
|  1 = button is pressed; 0 = button
|}
|}

Latest revision as of 02:05, 23 April 2019

Introduction

Parts in the Kit

In the kit you will receive:

  • ShiftX2 module
  • 4 wire pigtail
  • Acrylic enclosure
  • Mounting screws with o-rings

ShiftX2 components.jpg

Dimensions

  • ShiftX2 bare board: 143 x 85mm (5.6 x 3.27 inches)
  • ShiftX2 enclosure: 172 x 18 x 12.7 mm (6.x8 x 0.71 x 0.5 inches)

Installation

ShiftX2 is designed to be surface mounted with the included enclosure, or it can be embedded into your dashboard in a custom installation.

Assembling the enclosure

  • plug the wiring pigtail into the socket on ShiftX2. The plug is keyed to insert in one direction, with the red wire to the left.

ShiftX2 pigtail.jpg

  • Thread the pigtail through the hole in the bottom layer of the acrylic enclosure (1/8" black plastic plate).

ShiftX2 wiring base.jpg

  • Place ShiftX2 onto the bottom layer, stack the 1/4" middle frame on top, with the clearance notch over the connector, and finally the top clear lens.

ShiftX2 top lens.jpg

  • Place the two o-rings onto the mounting screws - these cushion the mounting points of ShiftX2 - and place them into mounting holes, passing through all 3 layers of the enclosure.

ShiftX2 screws.jpg

ShiftX2 assembled.jpg

Mounting ShiftX2

Mount ShiftX2 to your dashboard surface using the following template: ((picture))

  • Note: Ensure the hole for the wiring is deburred and has no sharp edges.

Attach ShiftX2 with the mounting screws and tighten until snug and the o-rings are compressed.

  • Note: Do not overtighten to prevent cracking of the acrylic enclosure.

Wiring

Pinout

Orientation is left to right looking into board connector:

Color Assignment Notes
Red 9-12v Power Connect this to switched ignition power. 0.5A max consumption.
Black CAN High
Yellow CAN Low
White Ground

Integration with RaceCapture / PodiumConnect

We recommend connecting ShiftX2 to CAN2 of your RaceCapture or PodiumConnect system.

Direct Wiring

For RaceCapture/Pro MK3, RaceCapture/Apex and PodiumConnect, we recommend direct wiring to the CAN bus connections provided by your system.

Shiftx2 direct wiring.png

For RaceCapture/Pro MK2 or RaceCapture/Track MK2 using the RJ45 connector, you can use a commonly available RJ45 splitter and RJ45 network-style extension cables to conveniently connect both OBDII and ShiftX2 on the same connector. With ShiftX2 on CAN2, the OBDII port is free to continue to use CAN1, and ShiftX2 will receive power from the OBDII port.

Shiftx2 with splitter.png

Suggested parts:

  • RJ45 Splitter "Hub" shaped
  • RJ45 network cable Flat style round style
    • Note Any standard CAT5 or CAT6 patch cable should work, so long as it is not a cross-over cable.
Patching the RJ45 cable to ShiftX2

You will need to splice ShiftX2 to the conductors of the patch cable. Start by snipping the RJ45 connector off the end of a patch cable, and then expose the individual wires.

Rj45labeled.jpg

RJ45 power and CAN connection pinout
ShiftX2 connection RaceCapture Connection CAT5 EIA-T568B RJ45 cable
Red +12v Brown
White Ground Orange/White
No Connection CAN 1 High Orange
No Connection CAN 1 Low Green/White
Black CAN 2 High Blue
Yellow CAN 2 Low Blue/White

Note: These color codes assume EIA-T568B RJ45 cable (check printing on the cable to confirm)

CAN Termination

CAN termination is enabled by default. To disable termination, cut the CAN Term jumper on the bottom of ShiftX2.

  • Note: the termination jumper is located on the bottom side of the ShiftX2 circuit board, on the right side of the board when the push button is on the left. It is labeled CAN TERM

There will be a small trace between the two square pads - cut the trace carefully using a razor, or the sharp tip of a small jewler's screwdriver paying close attention to not damage adjacent traces. To restore the jumper, solder a bridge between the pads.

Powering and Connecting to RaceCapture

Power

To power ShiftX2, connect the red wire to switched 12v, and the white wire to Ground.

  • Note: You can use the same circuit for your RaceCapture system so they power up simultaneously.

CAN bus connections

Connect the black wire to CAN High, and the yellow wire to CAN Low.

  • Note: You can choose either CAN1 or CAN2 to drive ShiftX2. The CAN bus can be defined in the script you use to control ShiftX2.

Using ShiftX2

The LEDs and display on ShiftX2 are controlled by RaceCapture's Lua scripting capabilities. Built-in functions provide access to ShiftX2's capabilities. See the ShiftX2 Lua scripting reference for additional details.

Compatibility

ShiftX2 works with the following devices:

  • RaceCapture/Pro MK2
  • RaceCapture/Pro MK3
  • RaceCapture/Apex
  • RaceCapture/Track MK2
  • PodiumConnnect

Firmware Requirements

ShiftX2 requires RaceCapture/PodiumConnect firmware 2.15.0 or higher. Download the latest firmware

Navigation Buttons

Once ShiftX2 is powered and connected via CAN bus to your RaceCapture system, the left button will automatically trigger a page navigation on the RaceCapture app dashboard.

The following scripts assume ShiftX2 is connected to the 2nd CAN bus, and is the first ShiftX2 on the bus (ADR1 jumper default setting)

Disco Lights Demo

This is a test script that exercises all of the LEDs on ShiftX2. You can use this as a first time test, as it does not rely on any sensors.

Script

Copy and paste this entire script into the scripting window, replacing any existing script.

setTickRate(10)

function rndc()
  return math.random(0,255)
end

function onTick()
  for i=0,9,1 do
    sxSetLed(i,1,rndc(),rndc(),rndc(),0)
  end
  -- ascii characters between 0 and 9
  sxSetDisplay(0, math.random(0,9)) 
end

Sequential shift light

This script configures just a sequential shift light.

Script

Copy and paste this entire script, replacing any existing script:

  • Default is reading RPM via OBDII. You can change to direct RPM input in the script.
setTickRate(30)

-- Set ShiftX2 configuration parameters with default parameters
-- orientation: 0=normal, 1=inverted (display above LED bar)
-- brightness: 0-100%, 0 = auto brightness
-- can bus: 0=CAN1, 1=CAN2
sxSetConfig(0,0,1)

--config shift light
sxCfgLinearGraph(0,0,0,7000) --left to right graph, smooth style, 0 - 7000 RPM range

sxSetLinearThresh(0,0,1000,0,255,0,0) --green at 3000 RPM
sxSetLinearThresh(1,0,5000,255,255,0,0) --yellow at 5000 RPM
sxSetLinearThresh(2,0,6000,255,0,0,10) --red+flash at 6000 RPM

function onTick()
  sxUpdateLinearGraph(getChannel("RPM"))
end

Shift Light + Twin Alert Example

This script shows a more complete example that demos a sequential shift light + two alerts.

Assumptions:

  • Engine Temperature on the 1st alert LED, connected to first analog channel
  • Oil Pressure on the 2nd alert LED, connected to second analog channel

Edit the script to change the analog channels you want to monitor.

Script

Copy and paste this entire script into the scripting window, replacing any existing script.

setTickRate(30)

-- Set ShiftX2 configuration parameters with default parameters
-- orientation: 0=normal, 1=inverted (display above LED bar)
-- brightness: 0-100%, 0 = auto brightness
-- can bus: 0=CAN1, 1=CAN2
sxSetConfig(0,0,1)

--config shift light
sxCfgLinearGraph(0,0,0,7000) --left to right graph, smooth style, 0 - 7000 RPM range

sxSetLinearThresh(0,0,1000,0,255,0,0) --green at 3000 RPM
sxSetLinearThresh(1,0,5000,255,255,0,0) --yellow at 5000 RPM
sxSetLinearThresh(2,0,6000,255,0,0,10) --red+flash at 6000 RPM

--configure first alert (right LED) as engine temperature (F)
sxSetAlertThresh(0,0,205,255,255,0,0) --yellow warning at 205F
sxSetAlertThresh(0,1,225,255,0,0,10) -- red flash at 225F

--configure second alert (left LED) as oil pressure (PSI)
sxSetAlertThresh(1,0,0,0,0,255,10) --red flash below 15 psi
sxSetAlertThresh(1,1,15,255,255,0,5) --yellow flash 15-20 PSI
sxSetAlertThresh(1,2,20,0,0,0,0) --above 20, no alert

function onTick()
  --update RPM
  sxUpdateLinearGraph(getChannel("RPM"))

  --update engine temp alert
  sxUpdateAlert(0, getChannel("EngineTemp"))

  --update oil pressure alert
  sxUpdateAlert(1, getChannel("OilPress"))
end

Predictive Lap Timer Indicator

This script enables predictive lap time visualization.

How it works

A bar extends left or right from the center of the linear graph:

  • Green bar extending to the right indicates you're beating the best time
  • Red bar extending to the left means you're falling behind.
  • When you're close to the best time, the center blue LED illuminates.


Notes:

  • The script is designed for a +/- 10 second maximum delta - so if you're ahead or behind by 10 seconds, the linear graph will be fully illuminated center-right, or center-left.
  • You will need to complete a a full lap to train the predictive timer before the graph will update.

Script

Copy and paste this entire script into the scripting window, replacing any existing script.


-- Predictive time visualizer

--save best lap time
bestTime = 0

-- Set ShiftX2 configuration parameters with default parameters
-- orientation: 0=normal, 1=inverted (display above LED bar)
-- brightness: 0-100%, 0 = auto brightness
-- can bus: 0=CAN1, 1=CAN2
sxSetConfig(0,0,1)

--config shift light
sxCfgLinearGraph(1,0,0,200) --center-out graph, linear style, +/- 10.0 seconds in 0.1 sec resolution

sxSetLinearThresh(0,0,0,255,0,0,0) --red if you're falling behind best lap
sxSetLinearThresh(1,0,80,0,0,255,0) --blue if you're close to best lap
sxSetLinearThresh(2,0,110,0,255,0,0) --green if you're beating best lap
setTickRate(30)

function onTick()
  local predTime = getPredTime()

  local timeDiff = (bestTime - predTime) * 60
  -- rail values 
  timeDiff = math.max(timeDiff, -10)
  timeDiff = math.min(timeDiff, 10)
  --scale values from +/- 10 sec to a 0-200 scale
  timeDiff = (timeDiff + 10) * 10

  sxUpdateLinearGraph(timeDiff)

  --update best lap time if an updated lap time is available
  local lastLapTime = getLapTime()
  if lastLapTime < bestTime or bestTime == 0 then bestTime = lastLapTime end
end

Boost Gauge

This script visualizes a single analog input channel on the linear graph.

How it works

The script configures the linear graph, then reads an analog channel and updates the graph with the current value. In this case, the value represents boost level measured from a MAP sensor.

Assumptions

  • MAP sensor channel is on the first Analog channel, and reads in KPa - typically 0-255. You can also connect this to the MAP reading on OBDII (PID 11)

Script

Copy and paste this entire script into the scripting window, replacing any existing script.

setTickRate(30)

-- Set ShiftX2 configuration parameters with default parameters
-- orientation: 0=normal, 1=inverted (display above LED bar)
-- brightness: 0-100%, 0 = auto brightness
-- can bus: 0=CAN1, 1=CAN2
sxSetConfig(0,0,1)

--config shift light
sxCfgLinearGraph(0,0,0, 20) --left to right graph, linear style, 0 - 20 PSI boost

sxSetLinearThresh(0,0,0,0,255,0,0) --green starting at no boost
sxSetLinearThresh(1,0,10,255,255,0,0) --yellow starting at 10 PSI boost
sxSetLinearThresh(2,0,15,255,0,0,10) --red+flash at 15 PSI boost

function onTick()
  local map = getChannel("MAP")
  if map ~= nil then 
    --convert to PSI boost
    local boost = math.max(map - 100, 0) * .145038
    sxUpdateLinearGraph(boost)
  end
end

Manual control of ShiftX2

You can obtain low level control ShiftX2 by sending it direct CAN messages in Lua scripting. This is primarily useful if controlling a second ShiftX2 running on an alternate CAN ID.

  • Note: The built-in firmware support for ShiftX2 is focused on controlling one ShiftX2 in your system. - you can use a combination of the built-in functions to control the primary ShiftX2, and then direct CAN control for the second unit.

Example starter script that shows how to directly control ShiftX2:

-- What CAN bus ShiftX2 is connected to. 0=CAN1, 1=CAN2
sxCan = 0

-- 0=first ShiftX2 on bus, 1=second ShiftX2 (if ADR1 jumper is cut)
sxId=0

--how often ShiftX2 is updated
tickRate=30

--Brightness, 0-100. 0=automatic brightness
sxBright=0

function sxOnUpdate()
  --add your code to update ShiftX2 alerts or linear graph during run time.
  --Runs continuously based on tickRate.

end

function sxOnInit()
  --add your code for configuring ShiftX2. Runs once during startup

end

function sxOnBut(b)
  --called if the button state changes
  println('button: ' ..b)
end

---ShiftX2 functions
--===============
--Reference. Delete me to save space
--===============

--function sxSetLed(index,length,red,green,blue,flash)
--Set an individual LED
--index: LED index, starting at 0
--length: number of LEDs to set at once
--red: Red value (0-255)
--green: Green value (0-255)
--blue: Blue value(0-255)
--flashHz: Flash rate, in Hz; 0=no flash

--sxSetLinearThresh(thresholdId,segmentLength,thresholdValue,red,green,blue,flashHz)
--Setup a threshold for the linear graph
--thresholdId: Threshold ID to set. from 0-4. define in ascending order.
--segmentLength: Length of the segment when in stepped graph mode. ignored for smooth mode.
--thresholdValue: Value for this threshold.
--red: Red value (0-255)
--green: Green value (0-255)
--blue: Blue value (0-255)
--flashHz: Flash rate, in Hz; 0=no flash

--sxSetAlertThresh(alertId,thresholdId,thresholdValue,red,green,blue,flashHz)
--Setup a threshold for an alert indicator
--alertId: Id of the alert to configure
--thresholdId: Threshold ID to set. from 0-4. define in ascending order.
--thresholdValue: Value for this threshold.
--red: Red value (0-255)
--green: Green value (0-255)
--blue: Blue value (0-255)
--flashHz: Flash rate, in Hz; 0=no flash

--sxSetAlert(alertId,red,green,blue,flashHz)
--Directly sets an alert indicator
--alertId: Alert Id to set
--red: Red value (0-255)
--green: Green value (0-255)
--blue: Blue value (0-255)
--flashHz: Flash rate, in Hz; 0=no flash

--sxUpdateAlert(alertId,currentValue)
--Updates Current alert value, using the previously configured thresholds
--alertId: Alert Id to set 
--currentValue: Updated value

--sxCfgLinearGraph(renderStyle,linearStyle,lowRange,highRange)
--Configures the linear graph
--renderStyle: 0=left->right, 1=center,2=right->left
--linearStyle: 0=smooth/interpolated, 1=stepped
--lowRange: low range of the graph
--highRange: high range of the graph (ignored if stepped linear style)

--sxUpdateLinearGraph(currentValue)
--Updates the linear graph value, using the previously configured thresholds
--currentValue: Updated value
--===============
--End reference
--===============

function sxSetLed(i,l,r,g,b,f)
  sxTx(10,{i,l,r,g,b,f})
end

function sxSetLinearThresh(id,s,th,r,g,b,f)
  sxTx(41,{id,s,spl(th),sph(th),r,g,b,f})
end

function sxSetAlertThresh(id,tid,th,r,g,b,f)
  sxTx(21,{id,tid,spl(th),sph(th),r,g,b,f})
end

function setBaseConfig(bright)
  sxTx(3,{bright})
end

function sxSetAlert(id,r,g,b,f)
  sxTx(20,{id,r,g,b,f})
end

function sxUpdateAlert(id,v)
  if v~=nil then sxTx(22,{id,spl(v),sph(v)}) end
end

function sxCfgLinearGraph(rs,ls,lr,hr) 
  sxTx(40,{rs,ls,spl(lr),sph(lr),spl(hr),sph(hr)})
end

function sxUpdateLinearGraph(v)
  sxTx(42,{spl(v),sph(v)})
end

function sxInit()
  println('config shiftX2')
  setBaseConfig(sxBright)
  if sxOnInit~=nil then sxOnInit() end
end

function sxChkCan()
  id,ext,data=rxCAN(sxCan,0)
  if id==sxCanId then sxInit() end
  if id==sxCanId+60 and sxOnBut~=nil then sxOnBut(data[1]) end
end

function sxProcess()
  sxChkCan()
  if sxOnUpdate~=nil then sxOnUpdate() end
end

function sxTx(offset, data)
  txCAN(sxCan, sxCanId + offset, 1, data)
  sleep(10)
end

function spl(v) return bit.band(v,0xFF) end
function sph(v) return bit.rshift(bit.band(v,0xFF00),8) end

function onTick()
  sxProcess()
end

sxCanId = 0xE3600 + (256 * sxId)
println('shiftx2 base id ' ..sxCanId)

setTickRate(tickRate)
sxInit()

ShiftX2 CAN bus API

Overview

The CAN bus API provides the configuration and control interface for ShiftX2.

Two styles of control are available:

  • Low level control of LEDs - the ability to discretely set LED color and flash behavior
  • High level control - configuring alert thresholds and linear graph up front, and then providing simple value updates

CAN Messages

CAN base ID

CAN base ID is 0xE3600 (931328)

Altering the Base ID

Cutting the jumper ADR1 will add 256 to the base ID, allowing up to two ShiftX2 displays on the same CAN bus.

  • Note: the ADR1 jumper is located on the bottom side of the ShiftX2 circuit board, on the left side of the board when the push button is on the left. It is labeled "ADR1"

There will be a small trace between the two square pads - cut the trace carefully using a razor, or the sharp tip of a small jewler's screwdriver paying close attention to not damage adjacent traces. To restore the jumper, solder a bridge between the pads.

CAN Baud rate

500K and 1MB rates are supported.

500K is enabled by default; cut the jumper ADR2 on the bottom of ShiftX2 to enable 1MB.

  • Note: the ADR2 jumper is located on the bottom side of the ShiftX2 circuit board, on the left side of the board when the push button is on the left. It is labeled "ADR2"

There will be a small trace between the two square pads - cut the trace carefully using a razor, or the sharp tip of a small jewler's screwdriver paying close attention to not damage adjacent traces. To restore the jumper, solder a bridge between the pads.

Configuration / Runtime Options

Announcement

Broadcast by the device upon power up

CAN ID: Base + 0

Offset What Value
0 Total LEDs Total number of LEDs on the device
1 Alert Indicators Number of logical alert indicators
2 Linear Bar Graph Length Number of LEDs in linear graph
3 Major Version Firmware major version number
4 Minor Version Firmware minor version number
5 Patch Version Firmware patch version number

Statistics

Statistics information, broadcast periodically by device

CAN ID: Base + 2

Offset What Value
0 Major Version Firmware major version number
1 Minor Version Firmware minor version number
2 Patch Version Firmware patch version number

Set Configuration Parameters Group 1

Sets various configuration options.

CAN ID: Base + 3

Offset What Value
0 Brightness 0 - 100; 1 = dimmest; 100 = brightest; 0 = automatic brightness control using built-in light sensor.
1 Automatic brightness scaling (Optional) 0-255; default=51. adjust this value to adjust the relative gain of the built-in light sensor when in automatic brightness mode.

Set Discrete LED

A low level function to directly set any LED on the device.

CAN ID: Base + 10

Offset What Value
0 LED index 0 -> # of LEDs on device
1 Number of LEDs to set 0 -> # of LEDs on device (0 = set all remaining)
2 Red 0 - 255
3 Green 0 - 255
4 Blue 0 - 255
5 Flash 0-10Hz (0 = full on)

Alert Indicators

Alert Indicators are typically single LEDs or a group of LEDs treated as one logical unit. This is defined by the hardware configuration of the device.

Set Alert

Directly set an alert indicator

CAN ID: Base + 20

Offset What Value
0 Alert ID 0 -> # of Alert indicators
1 Red 0 - 255
2 Green 0 - 255
3 Blue 0 - 255
4 Flash 0-10Hz (0 = full on)

Set Alert Threshold

Configures an alert threshold. Up to 5 thresholds can be configured per alert indicator.

Notes:

  • If the current value is greater than the last threshold, then the last threshold is selected.
  • The first threshold may have a threshold value >= 0; remaining thresholds must be > 0

CAN ID: Base + 21

Offset What Value
0 Alert ID 0 -> # of Alert indicators
1 Threshold ID 0 - 4
2 Threshold (low byte)
3 Threshold (high byte)
4 Red 0 - 255
5 Green 0 - 255
6 Blue 0 - 255
7 Flash Hz 0 - 10 (0 = full on)

Update Current Alert Value

Updates the current value for an alert indicator. The configured alert thresholds will be applied to the current value.

CAN ID: Base + 22

Offset What Value
0 Alert ID 0 -> # of Alert indicators
1 Value (low byte)
2 Value (high byte)

Linear Graph

The linear graph mode provides visualizations for common scenarios:

  • Sequential RPM shift light where the progression is stepped
  • Linear bar graph to linearly indicate a sensor value
  • Center left/right graph to indicate +/- performance against a reference - such as visualizing current predictive time vs best time

Power up default configuration

Upon power up the linear graph is configured:

  • Rendering style: left->right
  • Linear style: stepped
  • Low Range: 0
  • High Range: N/A
  • Threshold :
    • Threshold value: 3000 / segment length: 3 / color RGB: (0, 255, 0) / flash: 0
    • Threshold value: 5000 / segment length: 5 / color RGB: (0, 255, 255) / flash: 0
    • Threshold value: 7000 / segment length: 7 / color RGB: (255, 0, 0) / flash: 5

Configure Linear Graph

Configures the options for the linear graph portion of the device.

Rendering style:

  • If left->right, linear graph illuminates left to right
  • If centered, values below the mid-point in the range extend from the center to the left, and values above the mid-point extend from the center to the right.
  • If right->left, linear graph illuminates right to left

Linear style:

  • if smooth, graph length is updated smoothly by interpolating the current value in-between LEDs
  • If stepped, creates the visual effect of stepped progressions by setting the segment length of the threshold configuration. High Range of configuration is ignored.


CAN ID: Base + 40

Offset What Value
0 Rendering Style 0 = left->right, 1=center, 2=right->left
1 Linear Style 0 = Smooth / interpolated, 1 = stepped
2 Low Range (low byte)
3 Low Range (high byte)
4 High Range (low byte) (ignored if linear style = stepped)
5 High Range (high byte) (ignored if linear style = stepped)

Set Linear Graph Threshold

Configures a linear threshold. Up to 5 thresholds can be configured

Notes:

  • If the current value is greater than the last threshold, then the last threshold is selected.
  • The first threshold may have a threshold value >= 0; remaining thresholds must be > 0

CAN ID: Base + 41

Offset What Value
0 Threshold ID 0 - 4
1 Segment Length 0 -> # of LEDs on device (ignored if linear style is ‘smooth’)
2 Threshold (low byte)
3 Threshold (high byte)
4 Red 0 - 255
5 Green 0 - 255
6 Blue 0 - 255
7 Flash Hz 0 - 10 (0 = full on)

Update Current Linear Graph Value

Updates the current value for the linear graph

CAN ID: Base + 42

Offset What Value
0 Value (low byte)
1 Value (high byte)

Notifications

Notifications related to events broadcasted from ShiftX2

Button State

Indicates a change in the button state

CAN ID: Base + 60

Offset What Value
0 Button state 1 = button is pressed; 0 = button