RaceCapturePro RPM: Difference between revisions

No edit summary
m (Brentp moved page RaceCapturePro2 RPM to RaceCapturePro RPM)
 
(4 intermediate revisions by the same user not shown)
Line 1: Line 1:
Getting the right RPM signal can be challenging depending on the engine and ECU. Here's a guide for connecting RPM on various vehicles and engines. We'll be adding vehicles as we have more information.
=Overview=
Here's a guide for connecting RPM on various vehicles and engines. We'll be adding vehicles as we have more information.


==I don't see my car listed==
==Electrical / Signal requirements==
If you're handy with wiring, look up your car's diagrams and look for a tach signal - either a signal feeding the instrument cluster, or a wire from the ECU feeding the igniter. Then [mailto:[email protected] email us] your findings or questions and we'll get your car added to the list here!
RaceCapture/Pro requires a relatively clean square wave signal in the range of  0-5v to 0-24v.
 
==Channel Configuration==
[[Image:RaceCapture_pulse_rpm_config.png|500px]]
 
After connecting the signal to an appropriate input, configure the input:
 
* '''Channel Mode''' : Select RPM, Frequency or Period (ms) or Period(us) mode.
* '''Timer Speed''': Slow, Medium, Fast. This sets the dynamic range for the input channel; you can adjust this for slower signals (better resolution at lower RPM) or faster signals (better resolution at higher RPM). For most RPM applications, use the default Medium setting.
* '''Pulse Per Revolution''': This is a divider used to dial in the correct RPM based on the number of pulses per crankshaft revolution. Typical values:
** 4 cylinder: 2 pulse per revolution
** 6 cylinder: 3 pulse per revolution
** 8 cylinder: 4 pulse per revolution
 
These values can vary based on the type of ignition- wasted spark, distributor, or coil-on-plug.
 
** '''Sample Rate''': Typically you will want a reasonably high sample rate when measuring RPM. 10 - 50Hz is ideal.
** '''Channel''': For RPM, simply choose RPM from the channel name; this is a well known name throughout the system; the dashboard's RPM screen will automatically pick up this channel when RPM mode is selected.
** '''Channel customization (gear icon)''': Here you can customize the channel name, set min and max values, units label and the logging precision.


Also, if you've successfully tested one of the unverified configurations below, drop us an email so we can make a note.
Also, if you've successfully tested one of the unverified configurations below, drop us an email so we can make a note.
Line 14: Line 33:
==Honda==
==Honda==
===B Series Motors===
===B Series Motors===
* Use pin A21 on OBD1 socket
[[Honda_B_Series_Guide#RPM|RPM on Honda B series]]
* Settings:
** Pulse per revolution: 4
** Timer Speed: Medium


==BMW==
==BMW==
===E30===
===E30===
(Needs Verification)
[[BMW_E30_Guide#RPM|RPM on the E30]]
 
Use the Black wire in the C101 plug feeding from the ECU to the instrument cluster.
 
'''RPM Configuration'''
* Timer Speed: Medium
* Pulse Per Revolution: 3


===E36===
===E36===
(Needs Verification)
[[BMW_E36_Guide#RPM|RPM on the E36]]
 
Use the wire connected to the instrument cluster #20, black wire. Also available on the round diagnostic connector at the back of the engine compartment (black wire, Pin #1)
 
'''RPM Configuration'''
* Timer Speed: Medium
* Pulse Per Revolution: 3


===E46===
===E46===
(Needs verification)
[[BMW_E46_Guide#RPM|RPM on the E46]]
 
You can tap into the engine TD/RPM signal from Pin 9 of the OBD-II port, available on all BMWs after 2000.
 
'''RPM Configuration'''
* Timer Speed: Medium
* Pulse Per Revolution: 3


==Ford==
==Ford==
===EDIS based ignition (1995-1999 engines)===
===EDIS based ignition (1995-1999 engines)===
You can tap in to the IDM or PIP output line of any EDIS-4, EDIS-6 or EDIS-8 module.
You can tap in to the IDM or PIP output line of any EDIS-4, EDIS-6 or EDIS-8 module.
==I don't see my car listed==
If you're handy with wiring, look up your car's diagrams and look for a tach signal - either a signal feeding the instrument cluster, or a wire from the ECU feeding the igniter. Then [mailto:[email protected] email us] your findings or questions and we'll get your car added to the list here!

Latest revision as of 05:26, 25 March 2017

Overview

Here's a guide for connecting RPM on various vehicles and engines. We'll be adding vehicles as we have more information.

Electrical / Signal requirements

RaceCapture/Pro requires a relatively clean square wave signal in the range of 0-5v to 0-24v.

Channel Configuration

RaceCapture pulse rpm config.png

After connecting the signal to an appropriate input, configure the input:

  • Channel Mode : Select RPM, Frequency or Period (ms) or Period(us) mode.
  • Timer Speed: Slow, Medium, Fast. This sets the dynamic range for the input channel; you can adjust this for slower signals (better resolution at lower RPM) or faster signals (better resolution at higher RPM). For most RPM applications, use the default Medium setting.
  • Pulse Per Revolution: This is a divider used to dial in the correct RPM based on the number of pulses per crankshaft revolution. Typical values:
    • 4 cylinder: 2 pulse per revolution
    • 6 cylinder: 3 pulse per revolution
    • 8 cylinder: 4 pulse per revolution

These values can vary based on the type of ignition- wasted spark, distributor, or coil-on-plug.

    • Sample Rate: Typically you will want a reasonably high sample rate when measuring RPM. 10 - 50Hz is ideal.
    • Channel: For RPM, simply choose RPM from the channel name; this is a well known name throughout the system; the dashboard's RPM screen will automatically pick up this channel when RPM mode is selected.
    • Channel customization (gear icon): Here you can customize the channel name, set min and max values, units label and the logging precision.

Also, if you've successfully tested one of the unverified configurations below, drop us an email so we can make a note.

All 2008+ Vehicles

For newer vehicles, simply follow our OBD-II setup guide and configure an RPM channel.

Coil + distributor based ignitions

You can tap into the high voltage flyback pulse from an ignition coil primary circuit by using the CoilX module. See Instructions

Honda

B Series Motors

RPM on Honda B series

BMW

E30

RPM on the E30

E36

RPM on the E36

E46

RPM on the E46

Ford

EDIS based ignition (1995-1999 engines)

You can tap in to the IDM or PIP output line of any EDIS-4, EDIS-6 or EDIS-8 module.

I don't see my car listed

If you're handy with wiring, look up your car's diagrams and look for a tach signal - either a signal feeding the instrument cluster, or a wire from the ECU feeding the igniter. Then email us your findings or questions and we'll get your car added to the list here!