map_chan(atsId, data, 6, 1, 1, 0)
map_chan(ctsId, data, 7, 1, 1, 0)
2 KB (170 words) - 06:01, 18 December 2016
--CAN channel to listen on. 0=first CAN channel, 1=second
--1 for Big Endian (MSB) mode; 0 for Little Endian mode (LSB)
2 KB (228 words) - 05:23, 27 February 2015
...riority is 0 - 2, with 0 = normal priority used for pit-to car alerts, and 1 - 2 reserved for future use.
* Priority 1 address: 0xA102 (41218) / 0xA103 (41219)
2 KB (268 words) - 01:19, 8 September 2020
CAN_chan = 0 -- 0=first CAN channel, 1=second
map_chan(rpmId, data, 0, 2, 1, 0)
3 KB (308 words) - 01:47, 31 July 2015
==Approach #1==
575 bytes (102 words) - 14:16, 23 May 2023
...shift light is by using the PWM / Analog output channels to trigger a 3 + 1 shift light output. In this case, we used 3 of the outputs to control the 3
* Shift light boards connected to PWM / Analog out 1 - 3; flash alert LED to the 4th output
2 KB (283 words) - 19:48, 19 December 2014
* Bytes: 1,2 (little endian)
* Precision: 0.1
2 KB (216 words) - 21:28, 28 February 2015
...nds, using the Unix time epoch of 1/1/1970 (number of milliseconds since 1/1/1970)
"Interval"|"ms"|0|0|1,"Utc"|"ms"|0|0|1,"Battery"|"Volts"|0.0|50.0|1,"AccelX"|"G"|0.0|0.0|25,"AccelY"|"G"|0.0|0.0|25,"AccelZ"|"G"|0.0|0.0|25,"Ya
3 KB (362 words) - 20:04, 10 December 2023
...CAN Low to the corresponding CAN High / CAN Low on the RaceCapture/Pro CAN 1 channel. See the [CAN_Bus_Integration|CAN integration guide]] for wiring de
--CAN channel to listen on. 0=first CAN channel, 1=second
5 KB (554 words) - 04:51, 21 July 2016
|1
|1
5 KB (585 words) - 03:34, 16 July 2015
** Find one that uses an 1/8" jack to plug into a conventional microphone connection. ''Do not use a U
* '''1/4" stereo phono plug'''
4 KB (625 words) - 06:44, 15 August 2012
...e="text-align: center; background: transparent; margin-left: 10%;" border="1"
|1.0||16
289 bytes (28 words) - 07:28, 23 July 2010
*'''Cluster 1:''' Connect A1 to ground
User outputs 1-4 + shift light output can be used to control the sequential shift light.
2 KB (294 words) - 07:08, 26 June 2008
CAN_chan = 0 --CAN channel to listen to 0=first CAN channel, 1=second
be_mode = 1 --1 for Big Endian (MSB) mode; 0 for Little Endian mode (LSB)
7 KB (799 words) - 16:39, 8 November 2016
addAnalog(1,'Batt', 10, 2, 0, 5, 'V', 1, 0)
addFreq(5, 'RPM', 10, 0, 0, 10000, '', 60, 1)
4 KB (517 words) - 16:32, 8 May 2018
*Processor (Pin 1 GND, Pin 16 +5v)
*MAP sensor ( pin 2 is GND, pin 3 is +5v. "dot" is next to pin 1 on solder side)
2 KB (372 words) - 00:38, 4 February 2007
...dforums.net/showthread.php?607-Autosport-Labs-RaceCapture&p=50287&viewfull=1#post50287 this thread] for extensive information and discussion on the EvoX
chBoost = addChannel("Boost", 100, 1, -14.5, 43.5, "PSI")
5 KB (660 words) - 22:45, 27 October 2017
=====1) Go to the YouTube video page and click share=====
934 bytes (136 words) - 23:26, 6 July 2023
...connections from the Sequential Shift light board to Digital Input/Output 1,2,3 respectively.
if r > 5000 then setGpio(2,1) else setGpio(2,0) end
3 KB (464 words) - 05:30, 3 March 2015
...AN2. Typically CAN1 is used, so you would use '''CAN 1 High''' and '''CAN 1 Low''.
...ness. Typically CAN1 is used, so you would use '''CAN 1 High''' and '''CAN 1 Low''.
3 KB (542 words) - 14:36, 31 March 2022
