...wire your CAN device to either CAN 1 or CAN 2 on the Molex connector. CAN 1 is recommended as that is what most Presets defaults to if your device has
...et cable (wired in T-568B) and cut one end off. To put the device on CAN 1 you would solder the CAN device's CAN High wire to the Orange wire for Pin
4 KB (774 words) - 19:50, 5 January 2021
* shiftx3.stl : Main housing for ShiftX3 - Qty 1 needed
* shiftx3_back_3dprint: Back cover for housing - Qty 1 needed
3 KB (488 words) - 04:44, 11 January 2019
...d rates. You can easily build an RJ45 CAN Crossover cable to swap the CAN 1 and CAN 2 channel wiring for that CAN device/system. You can either perma
...you will probably have to go into each channel and change it from CAN Bus 1 to CAN Bus 2.
4 KB (604 words) - 19:51, 5 January 2021
* 0.1 degree timing resolution
* Initial support for 36-1 trigger wheel; other trigger wheel configurations to follow
3 KB (343 words) - 04:45, 28 April 2014
...t/mjlj/mjljConfig_v3.2.1.exe PC Configuration/Tuning software, version 3.2.1] (requires firmware V2.8)
...ist/mjlj/mjljConfig_v3.1.2.exe PC Configuration/Tuning software, version 3.1.2 beta 3]
3 KB (417 words) - 03:48, 5 April 2007
|1 (White)
|1 (Orange / White)
3 KB (496 words) - 14:55, 21 June 2019
* 3-2-1 tubular manifold
* 1.6L 4AG 7 rib block
2 KB (219 words) - 06:01, 28 September 2008
...ator for Ford EDIS ignition module. This software generates a simulated 36-1 signal on the PC parallel port, to allow bench testing of the full EDIS / M
664 bytes (106 words) - 23:00, 18 May 2007
...tGpio(1,1) , it will stay on until you explicitly turn it off (ie. setGpio(1,0)
** state: (int / ''(since 2.10.0)'' bool) 1 / true = output active; 0 / false = output inactive
5 KB (874 words) - 19:48, 5 January 2021
* The power plug is a 5.5x2.5mm. Certain 5.5x2.1 may also work.
* CAN bus 1 and 2 are bridged together; you can disable this by breaking the PCB jumper
6 KB (867 words) - 01:58, 16 July 2019
...t/mjlj/mjljConfig_v3.3.1.exe PC Configuration/Tuning software, version 3.3.1] (Requires controller firmware 3.3.x)
...bs.net/asl_dist/mjlj/mjlJunior_V3.3.1.zip Controller Firmware, version 3.3.1] (includes firmware programming software)
4 KB (578 words) - 02:13, 3 September 2010
'''1 pole Selector Switch (chose one):'''
*[https://www.ebay.com/itm/SP4T-Rotary-Switch-MFR01-1-Pole-4-Position-Switch-and-27mm-Knob/111832631148 4 Position Switch] - $6
5 KB (823 words) - 20:00, 5 January 2021
...s 2, you will have to go into each TPMS channel and change it from CAN Bus 1 to CAN Bus 2.
..., after applying the Preset, you will have to go in and change the CAN Bus 1 to CAN Bus 2 for each TPMS channel.
6 KB (951 words) - 19:38, 5 January 2021
--CAN channel to listen on. 0=first CAN channel, 1=second
tempId = addChannel("EngineTemp", 1, 0, 0, 255, "F")
10 KB (1,353 words) - 15:36, 6 May 2016
local temp2 = getAnalog(1)
if rpm > 5000 then shiftLeds = shiftLeds + 1 end
3 KB (330 words) - 21:33, 10 January 2015
* 3-2-1 tubular manifold
* 1.6L 4AGE 7 rib block
2 KB (258 words) - 18:37, 28 September 2008
...wo CAN bus networks to our [[#Powered_dual_CAN_hub|Powered Dual CAN Hub]]. 1 meter length.
M8-4P male to M8-4P female cable extends a CAN bus network. Available in 0.5, 1, 2, 3, and 4 meter lengths. [[Image:add_to_cart.png|link=https://www.autosp
14 KB (1,931 words) - 14:21, 30 August 2023
===Analog Inputs 1-7===
===Analog/Frequency Outputs 1 - 4===
7 KB (1,100 words) - 04:20, 5 April 2016
===Analog Inputs 1-7===
===Analog/Frequency Outputs 1 - 4===
7 KB (1,169 words) - 14:55, 19 March 2018
** 1: Fix in progress
** < 1 Ideal
3 KB (428 words) - 20:12, 27 August 2022
